Search:

Type: Posts; User: Jeff Ramsey; Keyword(s):

Page 1 of 12 1 2 3 4

Search: Search took 0.02 seconds; generated 24 minute(s) ago.

  1. Replies
    28
    Views
    2,429

    I use a Lenox WOODMASTER CT 1"x.035", 1.3T(.051...

    I use a Lenox WOODMASTER CT
    1"x.035", 1.3T(.051 Kerf) on my Felder FB510 and the results are excellent.
  2. Replies
    4
    Views
    1,610

    Post dimensions and weight and your zip code so...

    Post dimensions and weight and your zip code so shipping can be calculated.
  3. Replies
    26
    Views
    5,139

    I’ve a D4R Pro and the dovetails are consistent...

    I’ve a D4R Pro and the dovetails are consistent and tight; so tight that I don’t test fit (a little glue and final assembly is it). I had a Keller and sold it; the Leigh is more flexible. Are you...
  4. Thread: Bluebirds!

    by Jeff Ramsey
    Replies
    36
    Views
    4,733

    I found that the Peterson design is the best. We...

    I found that the Peterson design is the best. We get bluebirds in our Peterson houses every year.
  5. Replies
    9
    Views
    1,353

    It came standard on my FB510 when I bought it...

    It came standard on my FB510 when I bought it (approx. 6 years ago). Maybe Felder changed the pricing options.
  6. At one point back in 2018 I asked Klingspor about...

    At one point back in 2018 I asked Klingspor about ceramic blocks when one of mine fell off and broke when I was changing the belt. The response I received follows. I pulled all my blocks off and...
  7. Excelsior Style Stanley No. 9 1/2 Block Plane

    This is an Excelsior style Stanley 9 1/2 block plane with approximately 75% japanning (it’s worn mostly on the palm knuckle, where these block planes have japanning wear). The blade is good but needs...
  8. I’ll take it. PM on the way.

    I’ll take it. PM on the way.
  9. Replies
    110
    Views
    40,344

    Thanks, Jim. Do you have it set up in your temp...

    Thanks, Jim. Do you have it set up in your temp shop? You have a Stinger, right?
  10. The challenge for the mortise cavity is that the...

    The challenge for the mortise cavity is that the taper will cut the butterfly plug from the bottom down (upside down), where the mortise cavity would have to be cut from the top down. The angle would...
  11. Replies
    110
    Views
    40,344

    I just saw this. I like the lead screws on the...

    I just saw this. I like the lead screws on the X/Y as my Shapeoko only has a lead screw on the Z, with belts on X/Y which seem to stay put and not slip. My circle-diamond-square test cuts are good....
  12. Replies
    60
    Views
    18,480

    I have cut sheet brass C360 on my Shapeoko XL...

    I have cut sheet brass C360 on my Shapeoko XL with good results; both lubricated and non-lubricated. For flat bottoms, there are at times shadows that can be seen depending on the area of the flat. ...
  13. I'll be using a square bottom, tapered bit --...

    I'll be using a square bottom, tapered bit -- likely 3/16" diameter. I always ease up on feed and plunge rates, and pass depth when I build the tool paths. The defaults that manufacturers offer, in...
  14. Jim, thanks for the reply. I’m stubborn so I’m...

    Jim, thanks for the reply. I’m stubborn so I’m going to try a tapered bit. 1.5 degrees is what I found so far. At a .5” thick key, 1.5 degrees is .013 at the bottom, which is marginal for PVA but at...
  15. Tapered Sides with a Moulding Toolpath for Butterfly Keys

    I've not been successful getting a VCarve moulding toolpath to cut a 1-degree slope down a butterfly key. The response from Vectric follows. Has anyone ever tried doing this with or without a...
  16. I do the same with my Wynn canister filter. I...

    I do the same with my Wynn canister filter. I pull it outside, and with a dust mask on, I use my backpack Stihl to blow it off.
  17. If you buy direct from Klingspor, it's $100 ($300...

    If you buy direct from Klingspor, it's $100 ($300 for free shipping). You can buy Klingspor products from distributors, but the 1-year warranty on the glue will dissuade me. From their site:


    ...
  18. This is an older thread, but I just had a...

    This is an older thread, but I just had a Klingspor 6" x 48" belt come apart at the seam almost immediately after replacing a belt that was on for a while and did the same thing. I contacted...
  19. Replies
    49
    Views
    6,504

    Niece Lumber has a fine selection of Festool...

    Niece Lumber has a fine selection of Festool products.
  20. Replies
    6
    Views
    970

    I changed half on all but the larger doors, where...

    I changed half on all but the larger doors, where I changed all, and they’re fine; they close softly. The only issue I have is the caps don’t stay very well on the older hinges.
  21. Replies
    15
    Views
    2,873

    I just went through this with American Rotary and...

    I just went through this with American Rotary and my 4HP 3-phase tool. They said twice the motor HP, so I bought their AR10 which is 10HP. Their tech support was very good.
  22. Replies
    14
    Views
    1,645

    My start capacitor went on my Oneida dust...

    My start capacitor went on my Oneida dust collection Baldor motor recently and I went straight to Grainger and bought Daytons. I replaced the run capacitor as well. Mechanically, they were...
  23. Replies
    27
    Views
    6,125

    I hung a 220v heater in my 900 sq ft, uninsulated...

    I hung a 220v heater in my 900 sq ft, uninsulated shop. I'm in southeastern PA, and I can get my shop to a comfortable 60 (dry) degrees on a cold day, and the heater does not run constantly.
    ...
  24. Replies
    14
    Views
    1,670

    You might consider a Shark Guard, which comes...

    You might consider a Shark Guard, which comes with a splitter (mine did; check the Craftsman package to be sure). You get dust collection, a splitter and anti-kickback pawls in one.

    Guard...
  25. I put a Bench Dog on my Unisaw, with a Jessem...

    I put a Bench Dog on my Unisaw, with a Jessem lift and it's served me well. The Bench Dog fence isn't great and it's on my list to replace with something better, but I've been procrastinating as...
Results 1 to 25 of 299
Page 1 of 12 1 2 3 4