Search:

Type: Posts; User: Mark e Kessler; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    20
    Views
    872

    Lol............

    Lol............
  2. Replies
    14
    Views
    843

    I would use either a paint grade Poplar, maple or...

    I would use either a paint grade Poplar, maple or pattern grade Mahogany, the only thing I use MDF anymore for is veneer layups.

    Mark
  3. Replies
    7
    Views
    445

    Thats the one I had...

    Thats the one I had...
  4. Replies
    7
    Views
    445

    Many moons ago I also had the JLT, think it had 3...

    Many moons ago I also had the JLT, think it had 3 levels and 12-16 clamps worked awesome for panel glueups

    Mark
  5. Replies
    34
    Views
    4,798

    Check Hermance. http://helixhead.com/

    Check Hermance. http://helixhead.com/
  6. I have the AD941 and its edge of being on a 20amp...

    I have the AD941 and its edge of being on a 20amp circuit, you need like 25 amps so obviously I installed a 30 amp with 10awg to the breaker the thing is Felders Flying Lead is 12awg - Stupid... if...
  7. Replies
    17
    Views
    825

    No, itís totally a better build then any of the...

    No, itís totally a better build then any of the below You can see it when you compare them side by side, I didnít even look at the cosmetic- but if thats your thing... Not sure if its worth the...
  8. Replies
    17
    Views
    825

    The Manual can be found with an online search,...

    The Manual can be found with an online search, one thing I noted in the exploded view was the detail they put into the table lift mechanism, gears and gas struts, if you look closely the sheet metal...
  9. Replies
    17
    Views
    825

    It’s been out for 6-8 months, the list is 2k,...

    It’s been out for 6-8 months, the list is 2k, There is a container of them arriving in October, not sure how many though. I do think they will raise the price in the next year.
    Mark
  10. Replies
    6
    Views
    1,170

    Sold, sold, sold

    Sold, sold, sold
  11. Replies
    17
    Views
    825

    Hammer edge sander HS 950

    Anyone put their hands on one of these? First impressions? As much as I would love to get an Oakley, Whirlwind etc I just donít have the space, I may not even want to give up the space for this.
    ...
  12. Here is a Felder k700s 110" slide with 49" rip...

    Here is a Felder k700s 110" slide with 49" rip capacity in a inside garage dimension of 23' x 23', drawing is slightly off but full stroke can be done. AD941 shown as well. Most of the time only the...
  13. Replies
    17
    Views
    1,406

    Interesting, I know its different but I have a...

    Interesting, I know its different but I have a Felder with the silent cutter block and get zero tearout on most woods/grain, I don't even pay attention to the grain direction anymore unless it is a...
  14. Replies
    6
    Views
    1,170

    No Problem, did you see the pics I posted?...

    No Problem, did you see the pics I posted? virtually no tear out at all if any. "No bottom tear out" blades are a Fallacy, there will always be some. The only way you could lower the chances of tear...
  15. Replies
    22
    Views
    2,104

    As I understand it this blade will require more...

    As I understand it this blade will require more maintenance as far as keeping it clean as there is just not a lot of room for the pitch to go or build up and then of course if you hit anything metal...
  16. Replies
    14
    Views
    1,399

    I think this one was closer to 250k... 40' u...

    I think this one was closer to 250k... 40' u shape P&G boardroom table, that cost also included the table in the center. If I remember correctly the stainless steel inlay was 20k.
    412612
  17. Replies
    6
    Views
    1,170

    I am getting 0.128, i think my mic is out of...

    I am getting 0.128, i think my mic is out of calibration, its like 25yrs old. So probably 0.125. i will bring the mic to work tomorrow and check is calibration.

    Also reason for selling is I bought...
  18. Replies
    6
    Views
    1,170

    Additional pics... 1st is bottom crosscut on...

    Additional pics... 1st is bottom crosscut on Birch ply, second is top of cut with grain (different piece)

    Bty, my arbor is out like 0.008, this was measured at the thickness of cut pretty much...
  19. Stop lying to yourself...you need it... lol

    Stop lying to yourself...you need it... lol
  20. Replies
    14
    Views
    1,399

    Guess I am in a different camp, I have only ever...

    Guess I am in a different camp, I have only ever needed a 12" and a 6" square and have built everything from 200k boardroom tables to cutting boards and never needed anything else, I suppose if you...
  21. Replies
    6
    Views
    1,170

    Forrest duraline Hi-AT

    80t, 12Ē, 1Ē arbor. $95 shipped conus.

    Despite it appearance this blade has very little use, there is quite a bit staining on the plate that will not affect its performance. Appears to be small...
  22. Replies
    0
    Views
    454

    Tormek planer blade jig SVH-320

    Tormek planer blade jig SVH-320
    $150 shipped conus. Used a few times, sold my straight knife jointer and now have an insert head412541412542
  23. Replies
    14
    Views
    1,399

    I bought a few on ebay, 2 of the rules got lost...

    I bought a few on ebay, 2 of the rules got lost in shipping because I am guessing they just throw them into the usps envelope without any other packing and they cut their way out. I tried to contact...
  24. Replies
    22
    Views
    2,104

    Thanks for the info, it would be going on a k700s...

    Thanks for the info, it would be going on a k700s

    Mark
  25. Replies
    22
    Views
    2,104

    Thanks, assuming if you hit a nail your screwed...

    Thanks, assuming if you hit a nail your screwed but other than that seems if you could eliminate multiple blades and resharpening (i have heard that they stay sharp wicked long) it might be worth it,...
Results 1 to 25 of 90
Page 1 of 4 1 2 3 4