Search:

Type: Posts; User: Walter Plummer; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.26 seconds.

  1. Replies
    17
    Views
    1,030

    Here is another option for close work. ...

    Here is another option for close work. https://www.mscdirect.com/product/details/93712990. You line up on your marks through the optic then replace the optic with the punch and strike to mark your...
  2. Replies
    5
    Views
    488

    Not now but I am pretty sure I was on it last...

    Not now but I am pretty sure I was on it last evening.
  3. Replies
    39
    Views
    2,784

    I'm late to the thread but I had both shots with...

    I'm late to the thread but I had both shots with no problems at all. Moderna for me .
  4. If you are putting it between two sheets why not...

    If you are putting it between two sheets why not just screw everything together? No glue to worry about, reversible if something goes south.
  5. Replies
    20
    Views
    1,274

    It also sounds like you have to large a gap...

    It also sounds like you have to large a gap around the bit. Tighten it up as small as possible. The length is giving you a lot of leverage to over come the feather board.
  6. Replies
    6
    Views
    944

    WOW. A lot to drool over. Thanks for posting it.

    WOW. A lot to drool over. Thanks for posting it.
  7. Replies
    29
    Views
    1,606

    Do you have the hardware in hand? When I did one...

    Do you have the hardware in hand? When I did one similar only the "top" 2 inches of the bolt was 1/2" diameter. I think the connecting rod was only 1/4". We routed a groove and plugged it. Look into...
  8. Replies
    90
    Views
    12,379

    I watch a lot of you tube. All that I regularly...

    I watch a lot of you tube. All that I regularly watch are very upfront about whether or not the tools/products were purchased or sponsored. From there it's up to the viewer to weigh the information...
  9. Replies
    39
    Views
    1,536

    I have a 6' Starrett. It takes two hands to move...

    I have a 6' Starrett. It takes two hands to move it around. This is a good thing when marking or cutting but sometimes hinders getting it "on the marks" by myself. I also have a 12 foot Starrett rule...
  10. Replies
    23
    Views
    1,374

    We have a 12 tooth full kerf blade for thick...

    We have a 12 tooth full kerf blade for thick stock. Yes it leaves a rough surface but has no problem going full depth.
  11. Replies
    36
    Views
    3,214

    The tops are solid slabs, not laminated. Matt...

    The tops are solid slabs, not laminated. Matt sawed them and they were dried in a vacuum kiln. Him and the gentleman with the kiln are investigating if there is a workbench market for the dried slabs.
  12. Replies
    20
    Views
    1,190

    We use one of these at work for packaging. Air...

    We use one of these at work for packaging. Air and electric. Sticks are 1" Dia. x 3" long. Pumps a lot of glue. 441452
  13. Have you made sure the bottom wheel is not moving...

    Have you made sure the bottom wheel is not moving on the shaft ? Or for that matter that the shaft is not shifting ? I have seen weirder things. keep us posted.
  14. 5 Months? If my wife even saw the snake we would...

    5 Months? If my wife even saw the snake we would be gone leaving the house and everything behind.
  15. One more where it's just going to pay this years...

    One more where it's just going to pay this years taxes.
  16. Replies
    12
    Views
    813

    I also meant to say that for any cutting problem...

    I also meant to say that for any cutting problem weather it's a saw, router, even a drill the first thing to try is change the blade or bit or drill and see if you still have the problem.
  17. Replies
    12
    Views
    813

    Have you tried a different bit? What type bit are...

    Have you tried a different bit? What type bit are you using? Straight , Spiral up? Are you hand feeding or are you using a hold down of some kind? If you are hand feeding and the stock is bowed that...
  18. Replies
    5
    Views
    2,238

    This gentleman has some inspiring videos. On my...

    This gentleman has some inspiring videos. On my bucket list to try.https://www.youtube.com/channel/UC0RV-K22jKleJsEj2h5cPow/videos
  19. Replies
    19
    Views
    1,345

    The radial ram drills will swing 360*. If you...

    The radial ram drills will swing 360*. If you crank it all the way up I am guessing you could get 5' under the chuck. I may try it later just to measure. Here is a photo of my 1951 version.432009...
  20. I leave for work a little after 5 and there was a...

    I leave for work a little after 5 and there was a package on my stoop. No idea when it was delivered. Sometime between 9pm and 5 am.
  21. Replies
    10
    Views
    849

    Not speakers, but this guy is the one all the...

    Not speakers, but this guy is the one all the rest of the youtube machinist call when they need help. Check this video where he is making cages for ball bearings for his surface grinder. Around the...
  22. Check this guy out. ...

    Check this guy out. https://www.youtube.com/watch?v=_gqn6EBwPFk&t=6s
  23. Replies
    25
    Views
    1,190

    Still prefer paper and I balance every month. We...

    Still prefer paper and I balance every month. We were in the bank with an account representative and got to talking of this same thing. She told us we would not believe how many people come in throw...
  24. Photos of your track and rollers would help....

    Photos of your track and rollers would help. Depending on the track you may be able to cut an opening in the track to allow the trucks ("rollers") to drop out to remove the door.After trimming...
  25. Replies
    39
    Views
    2,173

    I made this one about 15 years ago.431585431586...

    I made this one about 15 years ago.431585431586 It has worked well.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4