Stu, is your saw a gear reduction saw, slowing the chain even more? Do you push very hard on it when milling? I'm trying to figure out if I am doing something wrong when I am milling with my...
Type: Posts; User: Todd Woodward; Keyword(s):
Stu, is your saw a gear reduction saw, slowing the chain even more? Do you push very hard on it when milling? I'm trying to figure out if I am doing something wrong when I am milling with my...
Mike, I wanted to say that my post was meant jokingly. I just reread it and it comes off a bit sarcastic. I was looking for something as well once and just decided to peel it off afterwards. I do...
Nice wood Stu, I made mine out of aluminum and it is light, I just need to find a good saw for it. I have access to an old Homolite Wiz 66 with a 30 inch bar. It is loud and the chain turns slow,...
I just screw the board to the log. Don't tighten it down to the point of twisting. I used a jointed and planed 2 by 6 and it works good for my set up, but a wider board would be better if running a...
I made my own and it was quite easy to do. I have a mid size saw on it and it is hard starting not to mention lacking power. I'm 55cc's and it isn't enough. Let's talk about work. Work, remember...
It's woodworking, not clamp works. You are so worried about keeping your clamps clean that your glue-ups are going to fail!!!!! If you took the time to actually prevent glue from getting on your...
My guess is that you were so worried about tensioning it properly that you didn't turn the wheels to check tracking as you tensioned it. This isn't a one time deal 9checking tracking). It must be...
Jim, I've used that saw with a 16 inch and an 18 inch bar and believe it or not, it can't pull 18 inches buried in the wood. It'll pull a 16 with a really really sharp chain, but it just doesn't...
Can you buy your lumber there or do you have to bring it with you? I am hoping to attend a class there at some point this winter. Is there parking in a lot or is it on the street? I'm thinking...
Here's the website address.
www.findyourspot.com/survey/Results.asp?ID=0A29494F49054326FD8136E1D3799D7A
my wife has a website saved in our favorites at home that I will send you. You answer their questions about your likes and dislikes in areas to live, along with temperature zones and a few other...
Why not cut the boards to 6 inches wide or less and glue them up? That whole process of jointing and planing should have taken less than an hour for 30 bdft total. It's not fast, but you'll get the...
Joe, the day you posted this I was giving my kids (3 years old and 11 months old) a ride on a 52 (I think) JD M/T. My father has it and 5 or 6 other antique tractors and we were up visiting. My...
Art, I had the same problem. My easy quick solution that has worked perfectly was to close all the downstairs air vents and open all the upstairs ones. Cold air falls. It will cool your entire...
I sold mine too. I do ride a three wheeler and four wheeler off road though. Too dangerous on the streets here.
Bob, Chet is right. You can usually find an old belt drive contractors saw for $100 or less. You'll be much happier with it. It's certainly quiter than you direct drive unit. Where are you...
charles is right. Why make a ladder for the thieves to get into your yard any easier? Good side goes out!!!
unless you were born 1 second before the event and lived for 100 years and 2 seconds!!! It happens every hundred years.
what section do you look under to find lumber? I look occasionally but never see any.
Congratulations Alan, I wish I couold have come to the opening. Hopefully I'll be able to come over the bridge to a class at some point this fall or winter. It looks like everyone had a lot of fun....
I'm still trying to figure out how you are doubling your veneer. You said you have a sheet and a half and then you say you have 3 sheets. which one is it? I say make your own veneer press and take...
I sure am!! Where in atlantic county are you?
you've got a dozen fish that are 5 foot 6inches long? Chicken wire will do the trick.
Yes there is. I forgot about them. I get their e-mails. I was trying to find something a bit closer and also haven't had the time to get over there yet as my wife and I had a baby a couple months...
I've been looking for one and even spoke with a few people about starting one. I'd sure like to find one. there is one up in marlboro at www.cjwa.org. You can check them out if you want. Hmmmm,...