Search:

Type: Posts; User: Tony Rodoracio; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    64
    Views
    17,202

    Going to be listing a used Hammer K3 winner here...

    Going to be listing a used Hammer K3 winner here in the classifieds, hopefully this weekend. Located near Boise, Idaho.
  2. Cody, It looks like the same base i have. I...

    Cody,

    It looks like the same base i have. I bought the Whiteside "specialty moulding" bit #3326. It worked perfect. Check it out on there website.
  3. Replies
    2
    Views
    2,240

    Got it. Thank You

    Got it. Thank You
  4. Replies
    2
    Views
    2,240

    PM's not going thru

    My reponses to messages aren't showing on my end. I'm a contributor and i did read the recent change. Any advice? Thanks, Tony
  5. Replies
    7
    Views
    1,308

    The problem was exactly what David had described....

    The problem was exactly what David had described. After sliding the table to its full fore and aft limits for 5-10 minutes, it gradually began extending the length of travel to where it should be. I...
  6. Replies
    7
    Views
    1,308

    Thanks for the suggestions guys. I did check the...

    Thanks for the suggestions guys. I did check the locking mechanism and it is not the problem. Also checked the trackway and it is clear.

    David, I will give your suggestion a try and see what...
  7. Replies
    7
    Views
    1,308

    Darn that picture! Sorry

    Darn that picture! Sorry
  8. Replies
    7
    Views
    1,308

    problem with sliding TS

    Went to change the blade today on my Hammer K3 winner and discovered I couldn't. The table will not retract far enough to access the blade arbor.

    Has anyone else had this problem? Hoping there...
  9. Great patch work Art. Thanks for taking the time...

    Great patch work Art. Thanks for taking the time to explain how you went about it.
  10. Replies
    169
    Views
    80,949

    Not trying to stir things up here anymore than...

    Not trying to stir things up here anymore than they already are, but why would Mr. Pentz be banned from a site that discusses dust collection if he has information that might be useful to others??
  11. Replies
    9
    Views
    2,673

    I will have to remember that one. Thanks Larry

    I will have to remember that one. Thanks Larry
  12. Replies
    34
    Views
    6,350

    I took about the same amount of time on my...

    I took about the same amount of time on my kitchen remodel. As most of us know, it aint easy working full time and trying to complete a large project at the same time. Had my share of minor goofs...
  13. Thanks for taking the time to post your review. I...

    Thanks for taking the time to post your review. I have been thinking about getting the same machine for some time. Enjoy!
  14. Replies
    14
    Views
    3,344

    Thanks for the insight Chris. Lonnie, I know...

    Thanks for the insight Chris. Lonnie, I know exactly how you must have felt. My neighbors are elderly and I would not want to subject them to that kind of noise. I think I will consider your approach...
  15. Replies
    14
    Views
    3,344

    I too am in S. California so the air temp is not...

    I too am in S. California so the air temp is not a concern. My concern has been the noise that would be directed right at my neighbor. Does any one know the decibel level when venting outside? I have...
  16. Very nice work Mreza. Thanks for taking the time...

    Very nice work Mreza. Thanks for taking the time to post the pictures on your progress.
  17. Replies
    3
    Views
    1,136

    I have the same A3-31 and can verify it is a good...

    I have the same A3-31 and can verify it is a good machine. My only issue was that the fence was very slightly concave from top to bottom but it was an easy fix. I am however getting ready to sell...
  18. Replies
    15
    Views
    3,505

    I have the great lakes casters on my MM20 and...

    I have the great lakes casters on my MM20 and they work very well. They are the same style as the Zambus.
  19. Replies
    22
    Views
    3,374

    OK, How did you get the raised panels in the...

    OK, How did you get the raised panels in the doors after the glue up?? They look awesome. Thanks for the video!
  20. Replies
    21
    Views
    3,574

    You probably need a pneumatic stapler. I have a...

    You probably need a pneumatic stapler. I have a Grex and it has handled any upholstery fabric and substrate.
  21. Good to hear Bill. I have mine waiting at home...

    Good to hear Bill. I have mine waiting at home but won't be there until Monday to try them out.
  22. Replies
    18
    Views
    4,062

    Another happy Tenryu fan here. Made in the U.S....

    Another happy Tenryu fan here. Made in the U.S. too!
  23. Thanks Bill. Good to hear it works as advertised....

    Thanks Bill. Good to hear it works as advertised. Just ordered mine.
  24. Replies
    15
    Views
    11,512

    Alan, Any plans for the same type jig for the...

    Alan,

    Any plans for the same type jig for the 22 1/2 degree lock miter bit?
  25. Replies
    3
    Views
    953

    Grinder

    David,

    I have the slow speed grinder with the Baldor motor that you are talking about. It is awesome! The motor is smooth and quiet and the wheels spin freely with no wobble. I would reccommend it...
Results 1 to 25 of 40
Page 1 of 2 1 2