Search:

Type: Posts; User: Thomas C Barron; Keyword(s):

Search: Search took 0.00 seconds.

  1. Use UVA coated birch plywood, about $55 per...

    Use UVA coated birch plywood, about $55 per sheet. Then use .75 inch x 1.5 inch solid maple or poplar (if you’re not a stickler in finish) rips for the edges and wall ledgers. Build it in place and...
  2. Yes, this is the quickest way. Overcut the...

    Yes, this is the quickest way.

    Overcut the circle a hair bigger than twice the laser burn thickness, then use a shaper or hand held router with a pattern cutting bit. It will quickly shave off...
  3. You can, in fact, get six pieces using a CNC. ...

    You can, in fact, get six pieces using a CNC.

    It’s a 2’ diameter circle, not a square, so there are no corners. The software will nest the six pieces off axis from each other in two rows of three...
  4. Replies
    17
    Views
    4,992

    If you want to get technical, there is only one...

    If you want to get technical, there is only one grade of MDF. There might be different manufactures that use a different glue that works better.

    I’m guessing that you might be confusing the...
  5. Hi...what is the benefit of having a VFD on your...

    Hi...what is the benefit of having a VFD on your cabinet saw?
  6. Replies
    5
    Views
    1,175

    Powermatic shaper spindle

    I have a Powermatic TS80 SAC shaper.

    Where can I purchase or find a 1-1/4” spindle for it?

    Thanks in advance...
  7. Replies
    4
    Views
    760

    Not specifically with a spiral cut but, but I...

    Not specifically with a spiral cut but, but I have noticed it vibrates up or down with other cutters.
  8. Replies
    24
    Views
    2,505

    Thank you, every one’s responses were helpful so...

    Thank you, every one’s responses were helpful so far.

    i bought it used, and don’t have the manual. I didn’t know the thermal was connected to the contactor, so that is helpful to know for future...
  9. Replies
    24
    Views
    2,505

    So, today I go in and turn on the compressor and...

    So, today I go in and turn on the compressor and it runs until shutting off at around 168psi. I drained the tank down, and at around 150psi it started back up to then again shut off at 168psi. I...
  10. Replies
    24
    Views
    2,505

    I guess I should have said it’s getting 120v to...

    I guess I should have said it’s getting 120v to EACH line in terminal.
  11. Obviously, it’s either the motor or the pump. ...

    Obviously, it’s either the motor or the pump.


    Normally, if the motor goes bad it gives off a burning smell. If a winding wire breaks it can give off a clacking sound like a fan or cards in your...
  12. Replies
    24
    Views
    2,505

    Here’s a picture of the contactor. The compressor...

    Here’s a picture of the contactor. The compressor is a 2002 model year, and it does NOT have a low oil sensor. It appears all original.


    I have had the unit for 1-1/2 years, and yesterday was the...
  13. Replies
    24
    Views
    2,505

    There was zero pressure on the switch. I bled the...

    There was zero pressure on the switch. I bled the tank down until it was empty. It then took about 5-10 minutes before it would start back up without me holding the contactor reset button down.
  14. Replies
    24
    Views
    2,505

    So...the pressure switch can overheat, and when...

    So...the pressure switch can overheat, and when it cools down start working again?
  15. Replies
    8
    Views
    2,274

    Rip 4 pieces of 3/4 inch plywood 4 inches wide x...

    Rip 4 pieces of 3/4 inch plywood 4 inches wide x 4 inches longer than the length & width of the window. Install the first piece vertically on the left side of the window by screwing it through the...
  16. Replies
    24
    Views
    2,505

    Contactor overheating

    I have an Ingersoll Rand Type 30 air compressor. It’s 7-1/2hp single phase 240v.

    When I first turn it on, it will run for a few minutes until it pressures up to 150psi then shuts off. If you...
Results 1 to 16 of 16