Search:

I haven't visited "The Creek" in a very long time. This group was so extremely helpful when I purchased my laser several years ago. I need your help again trying to work thru the selection for a...

If the faded area is 1/2" or less on both ends, give HQ a shot. I have one material that I have to do HQ and have been using HQ on this layout since day one.
One other thing that caused me to chase...

I can handle that. Would not have thought I could save it like that. I guess that with the finish completely worn off the top that I should strip and refinish all of the wood? If so, what would...

I hang out on the engravers section but I need help from the wood craftsman in repairing my mom's sewing machine top. She passed in 2000 and I've had her sewing machine since then, hoping to get it...

Bill, I've just reloaded my first five rounds and waiting to get to the range to try them out. I've read so many horror stories about kabooms that I pulled the bullets on the first five and reloaded...

I have three of these. Kind of pricey unless you will use them often. Really very well made - true machine shop grade presses.
http://roperwhitney.com/bench-medium-duty.html

EDIT...Removed post.

Pressure washing with light!

Thanks Scott...You The Man!

I tried to search for it but can't find it. A few weeks back there was a discussion here pertaining to a new Rowmark laser two ply material which engraved cleaner than existing Rowmark product - in...

We do a lot of 1" x 3" plastic. We apply a light coat of dish washing detergent prior to engraving. A quick rinse off takes care of all but the yellow and white which take about three swipes of a...

I have three of the style "A", each set for a different diameter punch. The puches are not hard to change out but I use all three sizes several times on a typical day.
...

I have some Rowmark plastic material (gray) that has been in the garage a little too long, I guess. When I try to peel the protective covering off, much of the adhesive residue is staying on the...

We do everything on laser now but prior to the TroTec we ran one Gravograph (M40) and three Rolands (2 - EGX20 and 1 - EGX300). All were good machines with different capabilities and operated well...

A suggestion on changing the charcoal charge, I drape cheesecloth across the support screen in the bottom of my scrubber and let the cheesecloth extend up the sides enough that when it is time to...

What they said.

I engrave everything from bottom up. I coat all plastic with a thin layer of dish washing detergent prior to engraving and do not use tape over the material. A quick wash after engraving cleans all...

Assuming the lens holder on your 300 is close to the same as on my 100 - Check to be sure the lens holder is tight and the lens is not rocking. On my 100 there is an "O" ring above the lens that...

I get my LaserMax material from JDS and the red and yellow are bowed (more on one side than the other) almost always. The other colors, not so bad but are bowed as well on occasion. . It does not...

Hi Gary,
Not much time to reply but on the subject of multiples - there are different ways to do this - this is just one I use.

For instance:
You have a part that is 1" x 3" and you want to do...

I've had to interrupt one long job due to weather. One of those summer boomers popped up out of nowhere. I had questioned my salesman about this when he did the install and so I followed his simple...

I get about three of those a week. Mark as Spam and carry on.

Well, I see it now...guess i was brain dead. Thanks.

EDIT: See it now...never mind.

My donation may have expired...is that the reason I can't see it anymore? I'll be gad to make another donation so I can list a printer. I thought before my last...

First I've heard of them, but that doesn't mean much. Just a personal observation about web sites in general: A supplier type web site that does not offer a physical (or at least a mailing) address...