Search:

Type: Posts; User: Richard Madden; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. As easy as they are to build, I'd make a wedgie...

    As easy as they are to build, I'd make a wedgie sled for each saw and router table. I built mine for the table saw and I cut straight slots in the base at both ends instead of a pivot hole and curved...
  2. Replies
    5
    Views
    847

    Alan, thanks for the advice. After waiting...

    Alan, thanks for the advice. After waiting several days for someone to reply I decided to wipe the piece with lacquer thinner and do some sanding (dry). I then sprayed with shellac and everything...
  3. Replies
    5
    Views
    847

    Finishing Question

    I'm working on a hollow sphere with piercing. After the hollowing and turning the outside of the sphere I sanded using a beeswax/mineral oil mixture that I often use. It cuts down the sanding dust...
  4. Replies
    12
    Views
    899

    Don't know where you are located, but Craigs List...

    Don't know where you are located, but Craigs List shows one for $200.00 in my area.
  5. Replies
    12
    Views
    899

    I'm sure I remember seeing a homemade outboard...

    I'm sure I remember seeing a homemade outboard rest here, but now I can't find it. Standard black pipe and elbows were used. I had thoughts of making one but never did.
  6. My homemade threading jig makes 14tpi and works...

    My homemade threading jig makes 14tpi and works well with domestic hardwoods. Given a choice between 12 or 16tpi, I'd go with the 12tpi for the same reasons mentioned by Dwight.
  7. Replies
    14
    Views
    1,783

    I've not needed to buy any for a long time so...

    I've not needed to buy any for a long time so haven't noticed pricing difference. I cashed in years ago. http://www.sawmillcreek.org/showthread.php?129366-Danish-Oil-on-sale&highlight=
  8. Replies
    17
    Views
    2,038

    Ron, See if there's a Fastenal store near you....

    Ron,
    See if there's a Fastenal store near you. They have 1" bar.
  9. Glen, Here's an old thread I posted several...

    Glen,
    Here's an old thread I posted several years ago that might help. http://www.sawmillcreek.org/showthread.php?144500-Vessel-with-threaded-lid&p=1470158
  10. Replies
    11
    Views
    1,691

    Tim, if you are looking for videos on hand...

    Tim, if you are looking for videos on hand chasing, Mike Mahoney has an excellent one "Hollow Forms and Urns". This is what inspired me to try hand chasing. One thing I'd recommend if that's the...
  11. Replies
    4
    Views
    1,335

    You might want to consider making a threading jig...

    You might want to consider making a threading jig yourself. Dick Mahaney here at SMC showed one several years ago, and with his permission I copied it. Not too expensive to build and it does a decent...
  12. Replies
    6
    Views
    1,358

    Do a search for The Walnut Log located in...

    Do a search for The Walnut Log located in Missouri. Jeff is the owner and distributor for Hampshire Sheen in the U.S.
  13. Thread: Redbud

    by Richard Madden
    Replies
    4
    Views
    1,072

    Absolutely, it's worth saving. I've turned just a...

    Absolutely, it's worth saving. I've turned just a few pieces of redbud...here's one. http://www.sawmillcreek.org/showthread.php?161900-Red-Bud-HF&highlight=
  14. Replies
    21
    Views
    4,086

    How about using a combination square with a...

    How about using a combination square with a centering head held against the grinding wheel. Then the platform can be adjusted to lay flat and true to the blade of the square? I think Cindy Drozda...
  15. Replies
    16
    Views
    2,230

    good idea!!!

    good idea!!!
  16. Replies
    16
    Views
    2,230

    You're not alone, Robert, this was new to me....

    You're not alone, Robert, this was new to me. Probably not too uncommon with cheaply made foreign made stuff.
  17. Replies
    16
    Views
    2,230

    You lost me, Mike. This night stand has three...

    You lost me, Mike.
    This night stand has three drawers, and no face frame, and no rail between the drawers. The inside top and sides are flush...even the drawer bottoms are flush. Very cheap. I think...
  18. Replies
    16
    Views
    2,230

    Drawer stops

    My son just showed me on facetime, a night stand purchased for my grandsons room, and the question about drawer stops came up. I'm familiar with the hinge type and the piece of wood screwed to a...
  19. Replies
    11
    Views
    2,341

    Remove the coating on formica by sanding, getting...

    Remove the coating on formica by sanding, getting it down to a thickness of around .020. Sharpen to a rounded point. Speed helps, but be careful!! After a little use sand the sides where the edge has...
  20. Replies
    11
    Views
    2,355

    I have some old Craftsman turning tools and the...

    I have some old Craftsman turning tools and the ones with brown handles are marked HSS. Some others with red handles don't say HSS, so they're probably carbon steel.
  21. Replies
    14
    Views
    2,873

    I see another blue ribbon in your future.

    I see another blue ribbon in your future.
  22. If you want to get some different jaws, by all...

    If you want to get some different jaws, by all means go ahead, I have several myself. Even with the different jaws I have, sometimes I'm turning a piece that won't fit the jaws. For instance, I...
  23. Replies
    7
    Views
    1,803

    That's a great looking box for a very worthy...

    That's a great looking box for a very worthy cause. You should be proud.
  24. Replies
    64
    Views
    12,105

    +1!!!!! Me too!

    +1!!!!! Me too!
  25. Replies
    12
    Views
    2,109

    You could try something like...

    You could try something like this....http://www.sawmillcreek.org/showthread.php?193652-Dyed-Ash-Bowl-(a-tribute-to-Bill-Neddow)&highlight=
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4