I’ve owned a Jet 12” lathe but not the one in your list. Also had the Delta previously and now own the Laguna. I chose the Laguna based on the fact it could go to the lowest speed. I use it...
Type: Posts; User: Clint Baxter; Keyword(s):
I’ve owned a Jet 12” lathe but not the one in your list. Also had the Delta previously and now own the Laguna. I chose the Laguna based on the fact it could go to the lowest speed. I use it...
I'd use on of the Big Gator drill...
I've ordered from fine-tools.com before, especially to get metric items that are also "difficult to find a US source" for. Shipping costs and time for delivery weren't too bad, though I haven't done...
I’ve had good luck using these for short tenons and/or dowels and plugs.
https://woodworker.com/5-piece-tenon-cutter-mssu-880-756.asp
Mine have a tendency to do some burning along the surface of...
I have both the standard one and the low profile ones in both normal kerf size and thin kerf as well. And I rarely, if ever, use any of those four. I purchased the Shark Guard years ago and pretty...
TSO has Power-loc clamps that might suit you. They install in the dog hole and then are tightened in place by a 5mm fastener from above the table. You might be able to just get their Power-loc dog...
Just produced over 175# over the weekend. A combination of brats, polish, sweet Italian sausage, breakfast sausage, chorizo as well as ground bulk. We typically add pork shoulder roasts or Boston...
Like John, I have all three, use them regularly and like them a lot. Would buy them again if they disappeared.
Clint
Took down a big old box elder that had lots of flame figure. Also had lots of burls and curl as well. It’s been drying for years now but many pieces still have flame present in them.
Plus one on Tajima. I used to use Stanley Fat Max’s, (purchased from the UK), but have switched to the Tajima line since getting them.
Clint
One thing that I didn't see mentioned here is that one is not responsible for paying back the amount the property was depreciated, but instead paying tax on the amount of depreciation against the...
Seeing’s how it was a 1099-NEC that was issued, they are considering you an independent contractor, being paid for services rendered. If it were a payment for rent, it should have been issued on Form...
Dont waste time putting 20A breakers in if you’re going with 10ga wiring. Put in the 30A breakers as they are for protecting the wiring, not the item that is connected to it. And the they will be set...
My outfeed table is mounted to my Incra rails. The table rests atop a couple pieces of aluminum angle that are fastened to the vertical face of the Incra rail. I sourced weld nuts and short bolts...
In late November of 2020, I purchased a Mr Heater 5.3 Kw forced air electric garage heater to allow me to work outside as I was converting a pole barn into a viable wood shop. I finally got the...
I picked up some of the Fazlok fittings from Woodworkers Supply, https://woodworker.com/fazlok-4-quick-disconnect-kit-mssu-960-805.asp
They are tapered fittings, but also have a positive lock on...
I just googled “keyhole mounting plates”. Is this what your after? I used these in the back of a mantle shelf in the way you describe where they worked nicely.
Clint
Have had issues with UPS, FedEx and USPS. Usually FedEx delivers at a decent hour but not so for the other two. You have no idea when they may deliver an item. I've checked at 8:00 PM and...
FWIW Lee Valley has brad point bits in both 25/64 and 10mm sizes. They also have a 10mm forstner bit for $10.50, much cheaper than the Bosch bit you referenced in an earlier post. More options to...
Red oak tends to bother me a little, but haven't had any serious reaction to it, just a little bit of a scratchy throat. No issues with white oak though.
I did have a severe reaction to some...
After significant research, I chose a Clore as well. However I got the 950, which is even larger than the 660 listed here. I wanted as much capability as I could get with the type of winters we can...
Plywood may have grain Telegraph through your veneer. MDF or better yet, MDO,would be better substrates to veneer to.
Clint
What’s funny is that I’ve never found this on any of the many remodeling and demolition jobs I’ve done over the years. Having said that, I just tore out an unwanted wall this week that had the spaces...
From the manual of the GLM 100c,
464975
Clint
Good luck
I have a corded Fein and a Fuel M12 Milwaukee. I also used to have the M12 predecessor that was available before they released the Fuel version. Since getting the Fuel M12, I haven't touched the...