Search:

Type: Posts; User: David Powell; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    10
    Views
    1,358

    Like Gordon, I have the Freud quadra-cuts for...

    Like Gordon, I have the Freud quadra-cuts for round overs (and dowel making) and Whiteside for just about everything else.
  2. As I recall from replacing the original...

    As I recall from replacing the original cutterhead with the Shelix cutterhead on my DW735, I did have to remove the straight blades.
  3. McFeely's for many years. Now use Tacoma Screw...

    McFeely's for many years. Now use Tacoma Screw which serves a good portion of the Pacific Northwest.
  4. Replies
    38
    Views
    5,364

    Thanks John. I now can't get the method for...

    Thanks John. I now can't get the method for calculating square roots out of my head.

    Dave
  5. Replies
    6
    Views
    828

    I have CMT's extension that I use solely with a...

    I have CMT's extension that I use solely with a bowl router bit; have had no issues with it. Not sure if I would want to use it full time for all routing requirements.
  6. Replies
    2
    Views
    709

    Rick, I saw the same video. And, as I have an...

    Rick, I saw the same video. And, as I have an immediate need for this application, went ahead and ordered one. I too was familiar with alignment issues with other brands but thought it was worth a...
  7. Replies
    12
    Views
    2,539

    The website that Gary was referring to is...

    The website that Gary was referring to is https://generaltoolsusa.com.
  8. Replies
    21
    Views
    1,698

    Packing tape on my cauls and wax paper on my...

    Packing tape on my cauls and wax paper on my clamp rails.
  9. Replies
    11
    Views
    1,725

    As an alternative to the plates, one can use the...

    As an alternative to the plates, one can use the router table fitted with a roundover bit with a diameter 1/2 of the needed dowel diameter. There was an article in one of the old ShopNotes magazines...
  10. I contacted them 2 years ago about their discount...

    I contacted them 2 years ago about their discount and was told it had expired. Had not tried it since then.
  11. Replies
    26
    Views
    3,525

    Another vote for the Beal Tilt box.

    Another vote for the Beal Tilt box.
  12. Replies
    25
    Views
    3,579

    I run my end grain cutting boards through my...

    I run my end grain cutting boards through my planer with a byrd head. But, I round over the edges with a 3/8 radius router bit before doing so, which removes the chance of blowout. And I take...
  13. I, too, have purchased from Bandsawbladesdirect...

    I, too, have purchased from Bandsawbladesdirect before for the Diemaster 2 blades I use. Most recently I purchased from Hastings Saw in San Rafael CA; great customer service.
  14. Replies
    15
    Views
    1,727

    Interesting, Bruce. I had never heard of a...

    Interesting, Bruce. I had never heard of a Certificate of Mailing.
  15. Replies
    40
    Views
    4,670

    Very nice, Shiraz. Great tip on using the spoon...

    Very nice, Shiraz. Great tip on using the spoon for the inlay.
  16. Replies
    14
    Views
    1,912

    Another vote for the medium LV shoulder plane.

    Another vote for the medium LV shoulder plane.
  17. Replies
    19
    Views
    2,233

    I also use an X-acto knife to slide in-between...

    I also use an X-acto knife to slide in-between the backer and tape after smoothing an edge down with my finger.
  18. Replies
    24
    Views
    1,987

    The Infinity setup gauge works well; as Michelle...

    The Infinity setup gauge works well; as Michelle stated these bits are a pain in the backside to use. By the way, the setup gauge was invented by fellow Creeker Alan Schaffter.
  19. Replies
    108
    Views
    14,068

    One of the trucks that my dad had in his business...

    One of the trucks that my dad had in his business was a 1950 Dodge power wagon that you could not shift gears unless you double clutched. He also had a 1939 Dodge panel truck that shifted with ease....
  20. Replies
    23
    Views
    1,955

    Mike, reading your paper caused me to recall my...

    Mike, reading your paper caused me to recall my college days. I enjoyed all my math classes until I got to dify q. I was never so happy when the course was behind me. Because of my results in the...
  21. Replies
    56
    Views
    7,392

    I have the old styles of both Jorgensen's cabinet...

    I have the old styles of both Jorgensen's cabinet master clamps and Bessey's k body; usually grab the Jorgensen first. Did pick up a couple of the new Chinese version of the cabinet master; they...
  22. Replies
    25
    Views
    3,067

    I'm also a fan of the Resaw King. As others have...

    I'm also a fan of the Resaw King. As others have mentioned, I also experienced the Timberwolf dulling sooner than expected.
  23. Replies
    25
    Views
    2,993

    I thought it was a joke, until I saw Peter's post...

    I thought it was a joke, until I saw Peter's post with the Amazon link.
  24. Replies
    21
    Views
    2,511

    I have a Grizzly keyless chuck with a JT33 taper...

    I have a Grizzly keyless chuck with a JT33 taper that replace a keyed chuck. Was able to get the arbor off the old chuck so had to buy a new one. Overall, the Grizzly works fine for my work needs.
  25. Replies
    27
    Views
    2,136

    Wow, this thread really takes me back. I recall...

    Wow, this thread really takes me back. I recall taking a computer course in 1968 as a required engineering course. The language used was Fortran IV. I recall having to punch the cards after...
Results 1 to 25 of 72
Page 1 of 3 1 2 3