Search:

Type: Posts; User: Darcy Warner; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    15
    Views
    343

    They have TP, disinfecting wipes, feminine...

    They have TP, disinfecting wipes, feminine hygiene products, and hardware. Seems essential
  2. Replies
    1,479
    Views
    118,391

    Sometimes the bearings get out of time on the 75...

    Sometimes the bearings get out of time on the 75 setup from short strokes, partial strokes, etc. Every so often a firm stroke of the beam back and forth will get them where they need to be, to allow...
  3. Replies
    15
    Views
    343

    I can get everything I need from mcmaster carr...

    I can get everything I need from mcmaster carr the next day, don't need no stinking amazon.
  4. Replies
    1,479
    Views
    118,391

    You should be able to get about 98" with a 10"...

    You should be able to get about 98" with a 10" blade, the beam in the correct position and the support arm in the correct spot on the saw.

    https://youtu.be/K6FTNzdFB0I
  5. Replies
    25
    Views
    733

    As a connoisseur of large bandsaws, there is a...

    As a connoisseur of large bandsaws, there is a difference in performance with different tensioning mechanisms, wheel styles, weight, etc.

    Knife edge style tensioning makes a noticable difference...
  6. Replies
    1
    Views
    74

    General Metalworking G&L surface grinder

    Just drug my old Gallameyer and Livingston no 30 surface grinder back out. It runs like a top, but needs cleaned up and set up. It's fairly heavy.

    429830
  7. Replies
    24
    Views
    951

    Fork lifts.

    Fork lifts.
  8. Replies
    15
    Views
    347

    Make sure to rinse it out really well, no...

    Make sure to rinse it out really well, no evidence that way.
  9. Depends on what you want to spend and if you can...

    Depends on what you want to spend and if you can deal with stuff being delivered to your shop or not. I ship freight to CA often.
  10. Replies
    12
    Views
    905

    Mills and Drills Made things, made some scrap too. 429618

    Made things, made some scrap too.

    429618
  11. Replies
    32
    Views
    1,396

    There in stock stuff is low, and if they don't...

    There in stock stuff is low, and if they don't have it, its usually a week until they get it and then ship it out.
  12. Replies
    32
    Views
    1,396

    New? Used? I really like the Fujis, they are a...

    New? Used? I really like the Fujis, they are a bit more complex if you want to start playing with settings.
  13. Replies
    18
    Views
    661

    I believe we will see a manufacturing shift with...

    I believe we will see a manufacturing shift with even more being done in house (this country). Another lesson in being self sufficient and not relying on other countries for all your goods.

    It...
  14. Replies
    18
    Views
    661

    I repair equipment, lots of stuff has been...

    I repair equipment, lots of stuff has been dropped off at my door with a note on it. Materials/tooling/supplies are a bit harder to find right now, but stuff is getting done.
  15. Replies
    32
    Views
    6,848

    I bunks get stacked as high as I can stack them. ...

    I bunks get stacked as high as I can stack them.
    I have a cantilever two sided rack for small/short run stuff to go on. My culls, rips, small quantity left overs gets stored vertically. Once every...
  16. Surplus center is the first place I look,...

    Surplus center is the first place I look, followed by ebay, American metric pulley is another source, but they sell looks of blank bore pulleys.
  17. I would use a sheave with a bushing. Bolt in...

    I would use a sheave with a bushing.

    Bolt in end of shaft with a washer pressing against pulley is fine, typical euro arrangement, but the sheaves usually have a slight taper or center bore...
  18. Replies
    10
    Views
    469

    They make it near me, I left several pieces...

    They make it near me, I left several pieces outside on different sides of the house. It wasn't very stable.

    Install t&g ipe porch flooring if is covered like a porch and you have air flow...
  19. I am not mentioning my preferred spots, but the...

    I am not mentioning my preferred spots, but the midwest does offer some wonderful sparsely populated areas for stupid cheap prices. Apparently no one likes 6 months of winter.
  20. Replies
    13
    Views
    474

    90% of my bandsaw work can be done with a 3/8"...

    90% of my bandsaw work can be done with a 3/8" 3tpi band. Not sure who makes the band stock, most blades are 18 to 20 feet long. I call my saw sharpener, tell him what I want and the lengths, they...
  21. Replies
    6
    Views
    378

    They take a 19' 6" blade, anywhere from 3/8 to 1...

    They take a 19' 6" blade, anywhere from 3/8 to 1 1/4" wide.
    For production batching of parts. Trace pattern, cut close to line and stack on cart for next operation.

    The tannewitz was originally...
  22. Replies
    6
    Views
    378

    Another interesting tid bit on the greenlee, it...

    Another interesting tid bit on the greenlee, it was in the Fisher Body co. plant in Pontiac, MI. probably bought new for that building when it opened. Be neat to find pictures.
  23. Replies
    6
    Views
    378

    Ball bearing, 7.5hp direct drive. I believe it...

    Ball bearing, 7.5hp direct drive.
    I believe it was originally owned by the Fisher Body Company in Pontiac, MI.
  24. Replies
    6
    Views
    378

    Big bandsaw Tuesday

    Moving some equipment around in my shop today and finally getting around to test firing some stuff I have had sitting for a year or so. I do have 3 more 36" saws, I should get a group shot.
    ...
  25. I have a few places picked out already, miles...

    I have a few places picked out already, miles from anyone.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4