Search:

Type: Posts; User: Philipp Jaindl; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    34
    Views
    3,452

    As numerously stated it is certainly true that...

    As numerously stated it is certainly true that application matters very much, and the lighter the tool the easier it is to work with over extended periods of time. Havent had any issues with lack of...
  2. Replies
    34
    Views
    3,452

    Battery Platforms (22/36/40V etc.)

    Good Day Folks,

    I know this may open, if indirectly, the color preference can of worms however quite curious on what/if theres a consensus and the opinions on the matter so here goes.

    With...
  3. To be honest you can get away with just a Tape...

    To be honest you can get away with just a Tape Measure for the vast majority of things though a Steel Ruler is very handy to have in many applications. Same thing goes with Squares a regular one will...
  4. Ok I'll contact the shop and send it back then....

    Ok I'll contact the shop and send it back then. Do have some leather lying about somewhere will give it a shot and see how that works out for me. thanks Dave
  5. Alright it cleaned up a lot better than i hoped,...

    Alright it cleaned up a lot better than i hoped, the pattern very good shape, bit more cleaning then a nice finish over it and we're good i'd say. Thanks for the help

    431440
  6. Replies
    26
    Views
    2,421

    Carving Knives, Japanese Chisels followed by the...

    Carving Knives, Japanese Chisels followed by the Rest of the chisels, i freely admit my Plane Irons arent sharpened as often as they mayhaps should be, taking them apart, de-greasing (keep em well...
  7. Replies
    7
    Views
    2,441

    For Fenceboards its probably less critical but...

    For Fenceboards its probably less critical but usually you wana put the Hollow towards whatever you're screwing/Nailing them to. That way they wont try to push the Nails/Screws back out when they...
  8. Sorry for the late reply i've been kept busy. ...

    Sorry for the late reply i've been kept busy.

    The Pattern stands just a hair proud from what i can feel through the dirt. Hesitant to use solvents on the old plywod but I'm probably way too...
  9. Pfeil 11/1 Uneven Factory Grind and a question on Stropping Tiny Tools

    Greetings,

    Finally got around to ordering some Tools and try some Figure Carving and detail work, the Tools arrived today and looking at the Pfeil 11/1, Veiner? i hope thats the correct term, one...
  10. I've seen that replacements are available, though...

    I've seen that replacements are available, though as said i want to try and preserve the original if possible. thanks at any rate.
  11. Bentwood Chair embossed? Seat restoration

    Greetings,

    New Project: got this nice chair of the Grandparents Attic, now restoring the Frame, which is in decent shape, is fairly straight forward cleaning it up, sanding, filling wormholes...
  12. I've been using a Pica-Dry Mechanical Pencil (2,8...

    I've been using a Pica-Dry Mechanical Pencil (2,8 mm Graphite lead) for years now, the leads are a bit softer and need resharpening more often but they last for ages, havent managed to break one...
  13. A lot of Variables on that: Sawblade Quality,...

    A lot of Variables on that: Sawblade Quality, Tooth shape and number, material cut, dimensions of said material etc. I dont think you should fixate yourself on some kinda interval, as long as cut...
  14. Replies
    11
    Views
    2,761

    Depends what kind of Edge you're after, the "how...

    Depends what kind of Edge you're after, the "how sharp is sharp" can of worms. Up to what grit does the Worksharp go?

    If you're refering to the DMT Dia Sharp 1200 Grit its a solid choice, same...
  15. Replies
    13
    Views
    1,141

    Noted, will browse through them, thanks again Jim.

    Noted, will browse through them, thanks again Jim.
  16. Standard Veneering practices should work just...

    Standard Veneering practices should work just fine, whatever you do to one surface needs to be done to the other to counteract the movement and keep the Workpiece from dishing and warping

    If...
  17. Replies
    19
    Views
    3,274

    I use a Straw Broom (i hope thats the right...

    I use a Straw Broom (i hope thats the right english term for it) works for basically everything, if necessary a regular hair broom for the fine stuff. Also got a couple brushes + Dustpans flying...
  18. Replies
    13
    Views
    1,141

    Thats one of the downsides of living in the...

    Thats one of the downsides of living in the middle of nowhere , well stocked libraries arent really a thing here (not that they would be currently open anyways) still thanks Iowell.

    Thats quite...
  19. Replies
    25
    Views
    2,833

    Generally speaking yes you try to finish it as...

    Generally speaking yes you try to finish it as far as possible and only do the necessary clean up after assembly to get ready for whatever Finish will be applied. Not using too much glue and masking...
  20. Replies
    22
    Views
    1,801

    Not a Metalworker so dont quote me on it but from...

    Not a Metalworker so dont quote me on it but from my limited knowledge Carbide chop saws arent meant for hardened Steel meaning it might dull the sawblade pretty fast or damage it not that it wont...
  21. Replies
    13
    Views
    1,141

    Thanks for the Replies, Ha Frederick I didnt...

    Thanks for the Replies,

    Ha Frederick I didnt think anyone would even remember that, been a journeyman a while now. The reality of daily life in the job is a far cry from the romanticised artisan...
  22. Replies
    32
    Views
    4,702

    I'll fully agree with Derek here, worked on a few...

    I'll fully agree with Derek here, worked on a few Benches and Loungers (i hope thats the right word) over the years and always used flat slats. Fitting alongside the desired curvature is mostly done...
  23. Replies
    13
    Views
    1,141

    Looking for Books

    Greetings,
    Didn't really know where to put it so i would request the mods to please move it to the right place. Most topics and similar questions I've come across were either quite old or very...
  24. Replies
    4
    Views
    1,401

    For anythings thats in contact with food or...

    For anythings thats in contact with food or drinks clear coat is your best bet, easy to clean and doesn't leave stains when something does spill. At least thats my opinion.
  25. Replies
    8
    Views
    1,966

    Ran into something similar with every piece...

    Ran into something similar with every piece ending up slightly too short about 1 to 2 mil the culprit turning out the be the trusty tape measure thats been dropped one too many times.

    Lesson...
Results 1 to 25 of 141
Page 1 of 6 1 2 3 4