Search:

Type: Posts; User: Jeremy Patrick; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    13
    Views
    490

    Maybe my timing measurement it a bit off. I was...

    Maybe my timing measurement it a bit off. I was guesstimating but it was probably far shorter than that since I was moving fairly fast. maybe a minute to a minute and a half is more like it. My...
  2. Replies
    13
    Views
    490

    Wanted to post a follow-up on this. 2 days ago I...

    Wanted to post a follow-up on this. 2 days ago I got out to the shop with the new gallon of 9300. Same issue more or less. Opened the gun up a bit more for a heavier coat but thinking maybe I was...
  3. Replies
    13
    Views
    490

    Also, what have you seen as the drying times for...

    Also, what have you seen as the drying times for 9300?
    For the closet door, by the time Iím done with the door the bottom portion is already nearly dry. Compared to the 6000 this seems really fast...
  4. Replies
    13
    Views
    490

    Good info, thanks Iím suspecting the batch of...

    Good info, thanks
    Iím suspecting the batch of finish more and more at the moment. Sounds like everything else lines up as the ideal scenario for proper spraying.
  5. Replies
    13
    Views
    490

    Not the purple gun, itís the more expensive one...

    Not the purple gun, itís the more expensive one in the 70$ range. I have the purple one too but as cheap as it is I have it more for parts than actual usage.
  6. Replies
    13
    Views
    490

    Thanks Jim. Looks like we're both on the same...

    Thanks Jim.
    Looks like we're both on the same page more or less. This gun comes with a 1.4mm needle. Seems the HF guns mention different needle sizes but nobody sells the other ones... I'm...
  7. Replies
    13
    Views
    490

    EM 9300 tip

    For those who spray EM 9300, I wanted to ask what size tip and or settings you have seen is needed to spray this product well.
    Have only sprayed 6000 prior to this and in comparison the 9300 seems...
  8. Replies
    11
    Views
    913

    I know there are two very different approaches,...

    I know there are two very different approaches, one with laserjet/toner and one with inkjet but the processes for each aren't interchangeable. I don't have a color inkjet so my focus has been on the...
  9. I donít have a disposable setup so temp...

    I donít have a disposable setup so temp containers are my go to for the time being.
    never have tried the other products you mentioned. suppose Iíll get there when I have a project that is best...
  10. Understood on the mixing. I was hoping with how...

    Understood on the mixing. I was hoping with how slow the first setting is that it wouldn't be overkill for something like this. But I won't tempt it if a gentle stir is all that is needed.
    This...
  11. TC Crosslinker best use suggestions

    Wanted to ask for input on what people have seen is a best use scenario for adding TC CL100 crosslinker to their products.
    Instructions were for 2-5% for total volume. Stirring while adding. Mix...
  12. Replies
    11
    Views
    913

    possibly true. I think the process in general...

    possibly true. I think the process in general will require a decent amount of trial and error. The examples show PC being used to transfer to bare wood but all the notes keep saying it should also...
  13. Replies
    11
    Views
    913

    The aim is for the entire piece of wood to be...

    The aim is for the entire piece of wood to be white with the image applied onto it.
  14. Replies
    11
    Views
    913

    Think I've seen that one already. I'm certainly...

    Think I've seen that one already. I'm certainly up for giving it a try though!
    Found a couple posting about various types of transfer, some with just regular copy paper. Acetone being one and...
  15. Replies
    11
    Views
    913

    Image transfer to wood

    Wanted to post here for insight on what people have seen for best results in image wood transfer.
    I have seen quite a few articles listing polycrylic as one of the best methods for transferring...
  16. Replies
    17
    Views
    728

    Such a wealth of knowledge Jim! Based on what...

    Such a wealth of knowledge Jim!
    Based on what you have said I probably am on the heavier end of my shellac application on this last project. I used a spray can for the two platters I just finished...
  17. Replies
    17
    Views
    728

    Ah, I see my wording mistake. Had the concept of...

    Ah, I see my wording mistake. Had the concept of water borne down for this but not the right words down for describing what I was thinking!
    For this and other questions regarding finishes Iíve...
  18. Replies
    17
    Views
    728

    Slight deviation on the topic: Is there or...

    Slight deviation on the topic:
    Is there or should there be a difference in appearance when spraying 9300 over 6000?
    One piece I was working with had 6000 sprayed on one side but I tried doing...
  19. Replies
    17
    Views
    728

    Got it. I figured water would be a possibility...

    Got it. I figured water would be a possibility since itís water based but wanted to ask.
    If I were to try it in my earlex then I canít see any other way than to thin. Have been eyeing that...
  20. Replies
    17
    Views
    728

    Which thinner are you referring to?

    Which thinner are you referring to?
  21. Replies
    17
    Views
    728

    Wanted to follow up on this. I brought the 9300...

    Wanted to follow up on this.
    I brought the 9300 in the house for 2 days and started spraying with it today.
    Iím curious though, compared to the 6000 this stuff is thick. I have been able to spray...
  22. Replies
    17
    Views
    728

    Got it. I figured if it was completely done for...

    Got it.
    I figured if it was completely done for it would be somewhat obvious when opening the can and trying to stir, viscous or not.
  23. Replies
    17
    Views
    728

    EM9300 got pretty cold...

    I have a can of the EM9300 that got a little colder than room temperature for a month or so. I am figuring it got down to around 40 to 50į. No freezing that I know of.
    I am doing some passive...
  24. Ah, I should have specified. All the shellac I...

    Ah, I should have specified. All the shellac I use is dewaxed.
    Main concern I have is how long the strain will take to fully cure. But if I could sealcoat it then I would speed up the process.
  25. no worries. glad to support! Given the stench...

    no worries. glad to support!

    Given the stench from it and not remembering the exact label I'm pretty sure it's oil based.

    I'm using a super blonde shellac for my other projects and I do have...
Results 1 to 25 of 146
Page 1 of 6 1 2 3 4