Search:

Type: Posts; User: Mitch schiffer; Keyword(s):

Page 1 of 11 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    12
    Views
    610

    My truck isn't set up for air brakes plus the...

    My truck isn't set up for air brakes plus the whole system excluding the breaks them selves are in pretty bad shape.
  2. Replies
    5
    Views
    568

    Sawstop sliding table

    Has anyone tried the newer heavier duty sliding table from sawstop? I haven't heard much if any about it. I have seen several unfavorable reviews on the smaller model. My local dealer hasn't sold or...
  3. Replies
    12
    Views
    610

    Is there a big difference in the hydraulic drum...

    Is there a big difference in the hydraulic drum vs disk between your 2 trailers?
  4. Replies
    12
    Views
    610

    Hydraulic trailer brakes

    I just picked up a bigger trailer and I currently has non functional air over hydraulic drum breaks. Im wondering if anyone has experience with the electric over hydraulic systems. I need to convert...
  5. Replies
    23
    Views
    1,647

    I have a jessem phenolic router table and I have...

    I have a jessem phenolic router table and I have the smallest powermatic poweer feeder on it. I drilled 2 of the holes through the lip on the back metal strut that supports the top. The other 2 holes...
  6. Replies
    6
    Views
    768

    I see a lot of poplar like that at my local...

    I see a lot of poplar like that at my local menards. I do buy it occasionally even though it is expensive there. I made some French doors out of mineral stained poplar similar to this a few years...
  7. Replies
    16
    Views
    1,165

    I had a 20 inch shopfox with a mobile base and it...

    I had a 20 inch shopfox with a mobile base and it was very easy to move around. The shopfox replaced a jet jpm15 and the Grizzly was replaced by a oliver 25 inch. There wasn't much I liked about the...
  8. Replies
    32
    Views
    4,250

    I have an update to this if anyone was curious. I...

    I have an update to this if anyone was curious. I did get this under contract. Im buying it on land contract for a 4 year term. Here are a few pictures I took while walking the property. There are...
  9. Replies
    17
    Views
    1,457

    Some inspectors in my area won't allow staples...

    Some inspectors in my area won't allow staples for sheating. I have never seen them used for framing. I only use nails for sheating.
  10. I have seen lots of these fora sale very cheap on...

    I have seen lots of these fora sale very cheap on Craigslist and they usually sit on the for a long time. I don't believe there is any value in these types of items.
  11. Replies
    4
    Views
    808

    If you have a local bessey dealer that might be...

    If you have a local bessey dealer that might be better to go though for your warranty. I have never had an issue with my k body clamps however I do have quite a few irwin parallels so the bessey...
  12. I will probably be the minority here but I had...

    I will probably be the minority here but I had the g0858 and I didn't like it. It seems underpowered to me. It is listed as a 3hp but seems to be weaker then the 2ho powermatic i had used prior to...
  13. Replies
    34
    Views
    1,934

    I have quite a few milwaukee m18 tools. I like...

    I have quite a few milwaukee m18 tools. I like most of them better then the dewalt flexvolt and the Marita 36volt. The high voltage batteries have a lower amo hour capacity so I haven't really seen...
  14. I have the x17. I have had it it for about 5...

    I have the x17. I have had it it for about 5 years. It has always worked good for me. I have probably ran 150-200 gallons through it by now. I would suggest you get a couple different length...
  15. I have a rotary surface cleaner attachment for my...

    I have a rotary surface cleaner attachment for my pressure washer that works very well for cleaning concrete. You can use muratic acid on any real tough spots. I would imagine you can rent a surface...
  16. Replies
    18
    Views
    1,622

    I try and stick with the fuel line from...

    I try and stick with the fuel line from Milwaukee. I have found them to be much nicer then just the regular m18 line. I also have the fuel worm drive that I like better then this style.
  17. Replies
    3
    Views
    576

    Order some from edge supply thanks

    Order some from edge supply thanks
  18. Replies
    3
    Views
    576

    Where to find 5/8 edgebanding

    I'm struggling to find 5/8" prefinished hot melt edgebanding in a larger roll then 25'. I have bought this off ebay for years in 250' rolls but now I can't seem to find it. I am trying to avoid...
  19. Replies
    5
    Views
    1,106

    Menards just started carrying the bessys. Menards...

    Menards just started carrying the bessys. Menards frequently have a 11% rebate. My understanding is home depot will match the after rebate price if there is a Menards close by. This only applies the...
  20. Replies
    10
    Views
    1,092

    52" rails are available for all pcs models. I...

    52" rails are available for all pcs models. I would think a rail that is 48" has been modified.
  21. Replies
    26
    Views
    1,846

    They are 1 1/16 bore, 3 inch stroke, I believe...

    They are 1 1/16 bore, 3 inch stroke, I believe the rod is 5/16 possibly 3/8. I did look for a extrusion that I could stack on top of the existing one however it was a odd size and the t track is not...
  22. Replies
    26
    Views
    1,846

    I'm not getting any defection of the miter gauge...

    I'm not getting any defection of the miter gauge but more of the bracket that I made and the rod of the cylinders. This shaper came with a cam clamp that was mounted to the post on the miter gauge. I...
  23. Replies
    32
    Views
    4,250

    There is a road up to the top of the hill and the...

    There is a road up to the top of the hill and the land at the top is reasonably flat. It is not land locked. And there is power to the property. There are some very steep part and others that are...
  24. Replies
    26
    Views
    1,846

    Ok I have an update on this I came up with a...

    Ok I have an update on this I came up with a different hold down but it has its own issues. There is too much deflection in the cylinder rod to hold a workpiece securely. If I crank up the air...
  25. Replies
    32
    Views
    4,250

    Luckily the river in this area is over a mile...

    Luckily the river in this area is over a mile wide so the water says a constant depth. Neither of these are in a flood plain.
Results 1 to 25 of 258
Page 1 of 11 1 2 3 4