Search:

It really depends on the person.
I recently loaned out a Festool 1400 for a few months to someone that needed to replace all of the doors and jambs in his house. I've seen him with tools though, so...

Steve

I've never used a 2000, but I do have a 2200OE, and it is a very nice tool.It doesn't show it's "true colors", until you throw some big work at it.
Mine was purchased to route out...

Any guide rail system can be used for a standard circular saw. You just need to make a carrier board for your saw.
You will lose some depth of cut, the thickness of the material you use to make...

Nice space Andrew.I'm envious for sure.
However, that mountain bike with the Italian leather saddle sure is interesting.That's not a Selle saddle, so it could be a San Marcos. None the less, now I...

Andrew

It sounds as if it's out of warranty, if so, there is nothing wrong with turning it over to many of the small motor repair shops available.
The electronic circuitry for a Festool is a...

Yes, that is the going rate. Highly figured walnut, especially Claro and Bastogne,have always been very expensive.
Depending on what you intend do with it, will determine whether or not it is worth...

Yep, all of them are dangerous. If it's fun, there's risk. It's just the way the world is.
Sometimes I work on my shotguns in the shop. :eek:
Gotta agree about ladders though. I have absolutely...

Patrick

Many years ago I repaired two large mahogany bowls. Both had cracked and had taken a different shape. They were estimated to be about 50 years old when I got them.
Those bowls sat in my...

Ken

I've always had good results with Seal-A-Cell, and Arm-R-Seal. Flood coat with the Seal-A-Cell, and wipe off excess. Let dry and follow up with Arm-R-Seal in the gloss level finish you like....

Mark

I have an 5HP, 850lb. commercial washing machine. Unloaded and with the water turned off to it, spinning dry, it will still dance around the floor if it's not bolted down.
If nothing...

Mark

Yes, it can be bolted to the floor. I would not use any type of dampener unless I needed to.Through bolt it through some dense, rubber matting, ie Stall Mat from Tractor supply.
A Hilti or...

Dave

The red sealant painted on those threads is fine. I know it feels dry to the touch, but once you begin to tighten it, the pressure and friction will make is conform to the threads. If you...

Lee
CT has safe storage laws. To meet the requirement really isn’t difficult, or costly. It doesn’t have to be a standing floor safe. A lockable metal box would do it.

Yes, removing the firing...

Roger

It does not appear, from a simple google search, that the safe storage law has passed. It also appears that it is targeted at residences with minors, and or adults with known mental issue....

Elmer

I have a Delta 14-651 Benchtop mortiser. In the beginning I had a lot of trouble with it, and actually broke the handle. I also thought the bits were sharp, and then learned I had to up my...

Richard

That is the ratio on the System Three website for their epoxies. They may have epoxy formulas that are different ratio's, but for their "run of the mill" two part epoxy, it is a 2:1 ratio....

From the system 3 website.

"All System Three® epoxy products can be measured by weight or volume. Pourable products can easily be measured by volume, but paste and putty products are most...

Edward

Like I stated, everything is relative.
People pay big money for Festool Guide Rails, and they're just a simple aluminum extrusion. I thought when Makita and others got into the game, the...

Edward

Each person has different needs, and abilities. If this helps a person, and they do not have the ability to make a fence, then it's worth it.
I have three of the their feather boards and...

Martins are special guitars.
My D-35 is now 45 years old, and I am its original owner. I can't play it as well as I used to. Arthritis, broken fingers, and torn tendons in my hands through the...

Tom

They make some nice stuff, and they're very nice people.

WL Fuller in Rhode Island.
It's what they make, and they sell direct to the public.
They have the most comprehensive line of drill bits you will find. If you need it, or can think of it, they've...

Dennis

Unfortunately, there really isn't an answer. I have an 18 year old, Rikon, 18" bandsaw that has never seen anything but a 1", 2/3 varipitch, TriMaster blade, or a 3TPI Starrett blade, also...

I'm with Keith. Ship it with a servicable blade so the customer can get it up and running.
IIRC, Dennis bought a 14" Grizzly? Get a few T-Wolves, and experiment.

You'd be surprised at how "not...

Don't believe that you are limited to buying from a dealer within driving distance of your home. Especially if buying new.
Cars dealers have to compete with all other car dealers, not just the...