Search:

Type: Posts; User: Bruce Clumpner; Keyword(s):

Page 1 of 14 1 2 3 4

Search: Search took 0.01 seconds.

  1. I experienced a similar issue where my helix...

    I experienced a similar issue where my helix 75watt lost both the ability to move the table up, but also to reset. Lived with it like that for a couple of months and moved the table up by hand...
  2. Replies
    3
    Views
    2,882

    Hey Marco... I've got two Epilogs hanging off on...

    Hey Marco... I've got two Epilogs hanging off on Harbor Freight blower, all hard-piped with waste-gates on each machine. More than enough to pull from both when the machines are cutting. They're...
  3. Replies
    12
    Views
    3,483

    Inside Font Navigator

    I assume you have all your fonts registered in Font Navigator, so use the app to copy them to an external drive (flash or hard drive). Inside Font Navigator, there's an option to copy fonts to...
  4. Hey Kev, The coating/paint is pretty thick. ...

    Hey Kev,

    The coating/paint is pretty thick. Not sure if it's paint or cerakote, but it's tough. So I did as you said, started low and fast to see how the paint reacted. Didn't dent it at low...
  5. Hey Chris, good tip with the simple green, I...

    Hey Chris,

    good tip with the simple green, I use ZIP 505 which didn't really work on the slag. I started at 100% power and 50% speed at full frequency, then progressed up down to 15% speed. ...
  6. Need Settings for CO2 Laser for Ka-bar knives with black finish

    I've been struggling with getting a clean burn with my CO2 on the black finished KaBar knives. Using my 40-watt epilog mini, it took about 5 runs and then a trip to the buffer to get anywhere near...
  7. Replies
    3
    Views
    1,053

    Thanks Ross, Would never had found them since...

    Thanks Ross,

    Would never had found them since I'm not a member of any promotional products groups.

    Bruce
  8. Replies
    3
    Views
    1,053

    Sourcing Eco Friendly award

    Searching for the source of this sustainable award. Anyone know who puts this together?...
  9. Replies
    7
    Views
    3,735

    Craig, Hope you finally got your set-up to...

    Craig,

    Hope you finally got your set-up to work. Since you're in Orange County, I've been meaning to connect, but finally had a tid-bit I thought could help if you get stuck again.

    Did you...
  10. Replies
    7
    Views
    3,735

    Craig, if you remove the switch, then you need a...

    Craig, if you remove the switch, then you need a cross-over cable between the pc and laser. See if that helps you to connect once you set the ip to the machine....
  11. Replies
    60
    Views
    16,132

    Since you don't have a maker space close by, I'd...

    Since you don't have a maker space close by, I'd suggest a road-trip over to Epilog in Colorado. I've heard they're happy to show you the ropes with their equipment...
  12. MAP gas works great, just be careful you don't...

    MAP gas works great, just be careful you don't soften the plexi too much as it will reform if you set it down hot.
  13. Anyone running a machine with an RF tube use one of these to monitor temp?

    Saw this while searching Home Depot this morning and thought it was interesting...

    https://www.homedepot.com/p/Weber-iGrill-Mini-App-Connected-Thermometer-7202/300509969

    Thought it might be a...
  14. Replies
    21
    Views
    2,768

    Or just take the time to re-draw in corel

    Or just take the time to re-draw in corel
  15. Replies
    7
    Views
    1,408

    What goes first when cleaned in a dishwasher, the...

    What goes first when cleaned in a dishwasher, the screenprinting or the seams on the cup.. machine washing is not good for either
  16. Replies
    9
    Views
    8,369

    I'd mask and paint fill, but also shoot a...

    I'd mask and paint fill, but also shoot a clear-coat before your color so there is no chance of the color bleeding into the grain. Should be a fairly easy process for you, get some 18" high-tack...
  17. Replies
    1
    Views
    1,081

    Pumpkins & Lasers make the news...

    it's officially a meme?

    https://5newsonline.com/2018/10/30/a-new-age-of-pumpkin-carving-people-carve-pumpkins-with-laser-beams/?utm_source=fark&utm_medium=website&utm_content=link&ICID=ref_fark
  18. Replies
    8
    Views
    1,879

    look at RB Fabrication in California. They cut...

    look at RB Fabrication in California. They cut custom acrylic shapes out of any thickness sheets, may even stock something already. Ask for Cesar.
  19. Replies
    5
    Views
    4,634

    switch over to cat-5 network connection......

    switch over to cat-5 network connection... Soooooo much better! not sure it will eliminate your issue, but could help. Make sure you have a cross-over or use a hub between computer & laser
  20. Replies
    11
    Views
    2,474

    Yes the clipart formats in Ver 4 will open in at...

    Yes the clipart formats in Ver 4 will open in at least x7...don't have x8 to try it out
  21. Replies
    11
    Views
    2,474

    CorelDraw Clipart

    Look through Flea-bay for old versions of CD... My favorite was version 5, had a whole library of clipart that's still good with the current version.......
  22. Replies
    23
    Views
    3,826

    Craig, What happens when you just overlay your...

    Craig,

    What happens when you just overlay your square with a box with a white fill and no outline? no trim, weld or join?
  23. Replies
    2
    Views
    900

    I agree with Gary, using the save as PDF option...

    I agree with Gary, using the save as PDF option in Corel is the best way to get proofs out of your production system. I even made a page template with the date, job and contact info that I drop the...
  24. Replies
    3
    Views
    2,317

    I use Krylon rattle-can products all the time. ...

    I use Krylon rattle-can products all the time. They're fairly fast drying (gold & silver about 10 minutes) and don't muck up the mask/transfer tape unless you let it set for longer than 18 hours.
  25. Replies
    13
    Views
    1,720

    Over Exposed or running too hot?

    Late to the thread, but it looks like it's over-exposed or ran too hot?... however that works with Cermark? The loss of detail could be causing your issue. (note the loss of detail in the caduceus)
Results 1 to 25 of 330
Page 1 of 14 1 2 3 4