Search:

Type: Posts; User: Kev Williams; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.30 seconds.

  1. Replies
    2
    Views
    47

    HF has this portable (1 and 2 gallon versions)...

    HF has this portable (1 and 2 gallon versions) that would work, plenty of pressure and has its own pressure regulator-- it'll cycle occasionally to be sure, but at only 57 decibels for the small one...
  2. Replies
    6
    Views
    107

    my BIL has x6 on the computer he uses here, text...

    my BIL has x6 on the computer he uses here, text comes in center justified, but still have to deal with text frames, so basically the same as x3.

    If I could just get x4 to center text, I could...
  3. Replies
    6
    Views
    107

    Corel X3 X4 importing DXF issues

    I've been putting up with this for like years now, maybe someone can help--

    I use x3 and x4 all day every day. X4 is perfectly fine for everything I do, except for ONE thing: When importing DXFs,...
  4. NOTE!! -Be sure to ask if tariffs/duty/etc is...

    NOTE!! -Be sure to ask if tariffs/duty/etc is included in the shipping cost-!
  5. Replies
    10
    Views
    425

    As to bank fees, banks are no different than...

    As to bank fees, banks are no different than satellite TV or cellphone companies; threaten to take your biz elsewhere to save money and they'll likely negotiate to keep your business...
  6. Replies
    55
    Views
    2,701

    OK, so I ordered up the Crucial SSD that Mike...

    OK, so I ordered up the Crucial SSD that Mike Henderson suggested a page & a half ago from Amazon yesterday, just showed up--

    So I go to the Crucial website for install info... This drive is...
  7. Check out IEHK.com- they import several types of...

    Check out IEHK.com- they import several types of machinery, laser engravers among them, and are based in Wayne PA, they have pics of the place and themselves on the 'about us' page- I emailed them...
  8. ^^ What John said ^^ :) 1064nm lasers pass...

    ^^ What John said ^^ :)

    1064nm lasers pass right thru glass, and they turn aluminum into molten goo near immediately, definitely hot enough to melt glass...
  9. I had that happen in the Triumph once, know what...

    I had that happen in the Triumph once, know what caused it? - Air assist turned my plastic into an air hockey puck ;)
  10. Replies
    10
    Views
    425

    Wells Fargo has saved my butt from ID thieves 3...

    Wells Fargo has saved my butt from ID thieves 3 times, caught and shut down the nonsense before I even knew it was happening. Kudo's...

    Then last October-ish, I had 2 Amex withdrawls, and 3 E-pay...
  11. Replies
    5
    Views
    337

    There's several ways to get SS black with a...

    There's several ways to get SS black with a fiber, annealing is really cool and very popular with the knife/sword/medical supply customers--

    Another way is the 'get it as black as you can as fast...
  12. Replies
    55
    Views
    2,701

    I found the problem- back around tax time I was...

    I found the problem- back around tax time I was suddenly missing most of my previous return records! So I thought I'd try Ccleaner's 'recuva' program- which worked wonderfully btw- but what I didn't...
  13. No, it didn't 'get it back again', the bottom...

    No, it didn't 'get it back again', the bottom line simply didn't skip so much. I took his pic, rotated it .2 right to correct the angle, and added the yellow lines... the horizontal lines are dead...
  14. Replies
    7
    Views
    375

    I love balsamic vinegar but know zilch about...

    I love balsamic vinegar but know zilch about vinegar in general, but I do know just from reading labels that balsamic vinegar contains lead- I've been curious how that happens-?
  15. Sorry that I calll servo motors 'servo steppers',...

    Sorry that I calll servo motors 'servo steppers', but while servo's don't mechanically step like basic stepper motors, servo's do indeed move in distinct steps determined by the distance between the...
  16. Replies
    154
    Views
    15,285

    Maybe I should hit these ebay sellers up for a...

    Maybe I should hit these ebay sellers up for a commission.. ;)





    (nah)
  17. I'm going to assume it has servo-steppers,...

    I'm going to assume it has servo-steppers, because that's classic dirty encoder strip engraving... Someone with a Trotec will chime in shortly to better explain, in the meantime you can probably find...
  18. Replies
    22
    Views
    1,007

    As per the OP's post, here's one I made in Oct...

    As per the OP's post, here's one I made in Oct 2016, see if it sounds familiar-?
    https://sawmillcreek.org/showthread.php?247860-Now-THIS-is-un-nerving-Beware-of-what-you-type&highlight=deburring
    ...
  19. Replies
    55
    Views
    2,701

    It doesn't but for $13 I can add this adapter--...

    It doesn't but for $13 I can add this adapter-- workable?

    411342
  20. Replies
    4
    Views
    233

    I have RDworks just to check out, but with no...

    I have RDworks just to check out, but with no machine connected I can't access any machining parameters, so best I can tell you is, you need to search the parameters for speeds such as 'min acc',...
  21. I watched a fire about to start in my big Triumph...

    I watched a fire about to start in my big Triumph about a week ago. Very interesting- how it happened was I was cutting a crapload of 1/8" w/black Rowmark Ultramatte in the machine like I do about...
  22. Replies
    5
    Views
    337

    I'm usually the LAST person to use the words "do...

    I'm usually the LAST person to use the words "do a search", but for this subject, I recommend an 'advanced search' using the words 'fiber black stainless', you'll catch a lot of threads with some...
  23. Replies
    154
    Views
    15,285

    I only have a rotary on my Triumph machine, but...

    I only have a rotary on my Triumph machine, but it's always returned 'home' after it's finished engraving- only time it doesn't is if I stop the machine before it's done, then where it stops is the...
  24. Replies
    55
    Views
    2,701

    No esata jacks, just three 1394's and a couple of...

    No esata jacks, just three 1394's and a couple of 'display' jacks on the back of the video card, which is getting replaced as soon as my new GTX-750 ti shows up...

    Just opened it up, inside I have...
  25. Replies
    55
    Views
    2,701

    so, what are the downsides to an external SSD?

    so, what are the downsides to an external SSD?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4