Search:

Type: Posts; User: Larry Frank; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.08 seconds.

  1. I used a DeWalt die grinder with a fine Kutzall...

    I used a DeWalt die grinder with a fine Kutzall burr for shaping.

    412807
  2. Replies
    6
    Views
    104

    Moral of the story is to find a really good...

    Moral of the story is to find a really good doctor. With technology today, they can get a great image of a herniated disk. Unfortunately, they can not always isolate what is causing back pain.
    ...
  3. I am glad you are happy with your testing. ...

    I am glad you are happy with your testing.

    Traverse testing locations are based on equal areas and not equal distance.

    The only good way to do the testing is with a long test duct to get...
  4. Good questions about doing a traverse. When I...

    Good questions about doing a traverse. When I tested using that instrument, I did a traverse multiple times. Also, to get accurate measurements, you must do it in a straight section of pipe. ...
  5. I did not find much at all. My wife found a...

    I did not find much at all. My wife found a vacuum cleaner for me to use.
  6. Replies
    23
    Views
    551

    Only one singer I would pay to see....Garth Brooks

    Only one singer I would pay to see....Garth Brooks
  7. Replies
    4
    Views
    365

    I bought a HF and it was terrible and got hot...

    I bought a HF and it was terrible and got hot quickly. The DeWalt that I bought was great and used a Kutzall burr with it shaping a rocking chair.
  8. Replies
    14
    Views
    469

    You should be able to get the the 6" DWV pipe and...

    You should be able to get the the 6" DWV pipe and fittings at Menards at a reasonable cost. That is where I got mine for my 5 hp DC.
  9. Replies
    31
    Views
    1,323

    I borrowed John Lanciani's instruments and made...

    I borrowed John Lanciani's instruments and made measurements of my system allowing of course with static pressure and amps. It was quite a big job to set up a test pipe and jigs to do repeatable...
  10. Replies
    6
    Views
    578

    It would be interesting to know what phone you...

    It would be interesting to know what phone you took the picture. Often, these problems happen with a iPhone.
  11. Replies
    31
    Views
    1,323

    The problem at the end of a pipe is unstable air...

    The problem at the end of a pipe is unstable air flow and creates unreliable measurements. This would be true no matter what instrument is used at the end of a duct. I have tested a fan anemometer...
  12. Replies
    31
    Views
    1,323

    If you are happy with a fan type anemometer, then...

    If you are happy with a fan type anemometer, then good for you. Measuring with such a device is just not accurate especially at the end of a pipe or hose.

    If you are interested enough try the...
  13. Replies
    31
    Views
    1,323

    Wood Magazine tested quite a few 1.5 hp Dust...

    Wood Magazine tested quite a few 1.5 hp Dust collectors and NONE of them reached 1000 cfm.

    I see what Grizzly provides for a performance curve but still have my doubts based on what similar DC can...
  14. Replies
    31
    Views
    1,323

    If it were me, I would get a larger dust...

    If it were me, I would get a larger dust collector. People seem to over rate dust collector performance.

    For example, I do not believe a 1.5 hp Dust collector will deliver 1000 cfm. Wood Magazine...
  15. Please be careful with your back. Once injured...

    Please be careful with your back. Once injured your back will always be at risk especially since you have herniated discs.

    Please believe me as I have a bad back( screws, links, battery,...
  16. Replies
    21
    Views
    998

    All my landline calls go to the answering machine...

    All my landline calls go to the answering machine with a message of "Please leave a message after the beep".
  17. I do this with PowerPoint and a Brother Laser...

    I do this with PowerPoint and a Brother Laser Printer. It is very accurate.
  18. Replies
    7
    Views
    571

    I I tried one metal gate and do not care for...

    I I tried one metal gate and do not care for them. I made my own for both 6" and 4" . They seal tight and self cleaning and less expensive.
  19. Replies
    7
    Views
    447

    Glad you posted this and your fix.

    Glad you posted this and your fix.
  20. One should take some of the cfm numbers with a...

    One should take some of the cfm numbers with a grain of salt. The HF unit even with the mods will not get you 1500 cfm and the 2 hp Grizzly will not get 1700 cfm. If someone claims the HF is...
  21. Replies
    20
    Views
    1,775

    My Nova Voyager DVR Drill Press has been really...

    My Nova Voyager DVR Drill Press has been really nice. The ability to change speeds so easily over a wide range is very useful. The chuck has extremely low run out.
  22. Replies
    12
    Views
    704

    If I want to finish a jig, I typically use...

    If I want to finish a jig, I typically use Shellac . It dries very quick.
  23. A couple of the mfg post reasonable fan curves. ...

    A couple of the mfg post reasonable fan curves. I wish that Wood Magazine would do some tests again. In the past they did some good work.
  24. If you enjoy tinkering, that is great. I would...

    If you enjoy tinkering, that is great. I would rather spend the time making sawdust. I need to move my Sawstop PCS to make room for using other tools. The Sawstop industrial base makes it so easy...
  25. Thread: Hvac....

    by Larry Frank
    Replies
    18
    Views
    1,321

    My system monitors humidity in the house and if...

    My system monitors humidity in the house and if get too high but temperature is cool enough it run a cycle to reduce humidity.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4