Search:

Type: Posts; User: John TenEyck; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.32 seconds.

  1. Replies
    62
    Views
    2,487

    Mike, you are entitled to your opinion, but to...

    Mike, you are entitled to your opinion, but to say that Unibond 800 is very toxic stuff far exceeds the actual hazard. Many of the products we use have risks. Following the manufacturer's PPE...
  2. Replies
    62
    Views
    2,487

    Sort of surprising TB III failed considering the...

    Sort of surprising TB III failed considering the ends of the laminations are tied together around the handle. There should be almost no stress on them.

    It doesn't take long to get familiar with...
  3. Replies
    2
    Views
    160

    Grain filler, sealer, and paint or opaque...

    Grain filler, sealer, and paint or opaque lacquer.

    John
  4. Replies
    12
    Views
    242

    I'm interested to see what dyed MDF looks like. ...

    I'm interested to see what dyed MDF looks like. Not something I would ever have considered.

    John
  5. Replies
    12
    Views
    242

    What specific product are you using?

    What specific product are you using?
  6. Replies
    1
    Views
    220

    The HF and other guns designed to run off...

    The HF and other guns designed to run off compressed air are not compatible with turbine units, even if you could get a coupling to connect the two together. Turbine guns are low pressure all the...
  7. Replies
    32
    Views
    2,201

    Thanks very much Tom. That's a possibility at...

    Thanks very much Tom. That's a possibility at some point.

    John
  8. Replies
    62
    Views
    2,487

    True, but if you look at the literature for PRG...

    True, but if you look at the literature for PRG you'll see that 1800 lbs/sq ft is not even close to what's needed for that product. That said, it does work ok in a vacuum bag as long as you apply at...
  9. Replies
    32
    Views
    2,201

    That's an interesting set up. I imagine you can...

    That's an interesting set up. I imagine you can dry a lot of wood in a batch.

    John
  10. Replies
    7
    Views
    419

    If its a non drying oil I would wipe it with the...

    If its a non drying oil I would wipe it with the appropriate solvent until it looks as clean as possible. This might take several wipings using lots of fresh rags. Then sand it really well, or hand...
  11. Replies
    62
    Views
    2,487

    [QUOTE=Brian Holcombe;2951151]I think creep also...

    [QUOTE=Brian Holcombe;2951151]I think creep also must be affected by design and accuracy of fit ups.

    I have a table in front of me that has been in direct sunlight hours a day, made with Titebond...
  12. Replies
    32
    Views
    2,201

    You must live somewhere really warm. My drier is...

    You must live somewhere really warm. My drier is in the low 70's in the morning. How will turning off the fans lower the temp? If you are using a solar drier covering the glazing with something...
  13. Replies
    62
    Views
    2,487

    Creep is the response of the glue to shear stress...

    Creep is the response of the glue to shear stress on the joint. In bending, thickness makes a difference in that thick lumber will deflect less than thinner stuff for the same applied load. With...
  14. Replies
    32
    Views
    2,201

    I use a 30 year old dehumidifier. I used to use...

    I use a 30 year old dehumidifier. I used to use it in my dehumidification kiln, which ran at a constant 110F. It never failed to work properly and easily condensed water out on the cold coils. The...
  15. Replies
    62
    Views
    2,487

    Leaving the joints clamped long enough to assure...

    Leaving the joints clamped long enough to assure the glue has dried sufficiently is always a good idea but it won't prevent creep afterwards. It's an inherent property of the glue itself. If you...
  16. Replies
    12
    Views
    1,900

    Let me start by saying there are people with a...

    Let me start by saying there are people with a lot more experience using this type of horizontal mortiser than me. What follows works for me. Pick what you like and seek input from others, too.
    ...
  17. Replies
    12
    Views
    1,900

    Yeah, don't put any body parts into that big...

    Yeah, don't put any body parts into that big spinning bit! I'm not sure about your machine, but with mine you can and should extend the blade guard attached to the back of the fence rearward over at...
  18. Replies
    62
    Views
    2,487

    Mark, are you aware that white vinegar cleans up...

    Mark, are you aware that white vinegar cleans up wet epoxy easily and completely? I never knew that until I read it on the back of a System Three T-88 bottle.

    John
  19. Replies
    62
    Views
    2,487

    Cold creep is shear (displacement) of the glued...

    Cold creep is shear (displacement) of the glued surfaces at room temperature, and happens when the shear stress exceeds the creep strength of the glue. It's often seen with joints that go out of...
  20. Replies
    12
    Views
    1,900

    I can't say for sure, Jeff as I haven't used any,...

    I can't say for sure, Jeff as I haven't used any, but I think so. I looked into buying some but the cost was so high that I chose to use end mills instead. What I can say for sure is the deep depth...
  21. Replies
    62
    Views
    2,487

    Unibond 800 works great, especially in a vacuum...

    Unibond 800 works great, especially in a vacuum bag where the pressures are low. Weldwood Plastic Resin Glue works well, too, but according to the instructions requires much higher pressures, higher...
  22. Replies
    12
    Views
    1,900

    Any end mill supplier should have what you need. ...

    Any end mill supplier should have what you need. I have bought them from McMaster Carr and at Amazon; turns out the end mills I got from both were made by Niagara Cutter. Just make sure the mills...
  23. Well it was worth a shot. I just looked at the...

    Well it was worth a shot. I just looked at the ingredients list you provided. There are several ingredients in it that would likely damage many finishes. You might give this product a shot before...
  24. That is classic frame and panel construction,...

    That is classic frame and panel construction, done to accommodate seasonal expasion/contraction of the stile/rail joints and of the panels within the rails.

    John
  25. Replies
    62
    Views
    2,487

    Any thermoplastic glue will creep if the...

    Any thermoplastic glue will creep if the temperature and stress is high enough to exceed the shear strength. I know lots of folks say they use PVA type glues w/o issue. I'm sure it's true as long...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4