Search:

Type: Posts; User: steven c newman; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.65 seconds.

  1. Replies
    8
    Views
    1,010

    Maybe I'm just Olde School....Have a Stanley No....

    Maybe I'm just Olde School....Have a Stanley No. 7c, Type 9...AND an Ohio Tool Co. No. 0-7...I think would be a Type 3.....both use a standard frog angle....both have 2-3/8" wide irons.....used...
  2. Am NOT real happy with that lid...:mad:..makes...

    Am NOT real happy with that lid...:mad:..makes this look like a casket. :eek: Threw away the lid, this morning....and also removed the rebate it sat in ( and NOT very well, either:mad:)..
    466771...
  3. Replies
    27
    Views
    1,200

    I go to 2,500 grit....then either the strop or...

    I go to 2,500 grit....then either the strop or the cloth wheel, with the Green Compound....Single,flat bevel....first 1/2"-1" of the back is also flat. tain't Rocket Science....

    One can get a...
  4. Replies
    11
    Views
    722

    Wasn't Goodell Pratt Co. taken over by Millers...

    Wasn't Goodell Pratt Co. taken over by Millers Falls back in the mid 1930s? Not sure what model number was used for either maker's version.....some had a brace already attached, just stick a bit...
  5. Work in progress... 466666 Lots of sanding to...

    Work in progress...
    466666

    Lots of sanding to do...and a bit pf work with a smoother, too
    466667
    trying to decide which will be the "Front" so I'll know where to add the hinges...and a...
  6. Replies
    11
    Views
    722

    The chains looked a bit..special.. 466660 ...

    The chains looked a bit..special..
    466660

    When I can find a bit of time..I need to clean this one up a bit...
  7. Clamps are off...board for the lid has been set...

    Clamps are off...board for the lid has been set aside...Monday...shop is closed.
  8. Replies
    11
    Views
    722

    Missing it's chain.. You use a loop of chain,...

    Missing it's chain.. You use a loop of chain, this will pull the chain AND the bit you are drilling into a beam. aka...Chain Drill. Sometimes set into a big brace, other times into a Breast...
  9. Hmmm... 466654 Most planes land here.. 466655...

    Hmmm...
    466654
    Most planes land here..
    466655
    Most of the rest of the ready-to-use tools are inside of this
  10. Hmmm, seems the "secret" to a glue up was LOTS of...

    Hmmm, seems the "secret" to a glue up was LOTS of cussing:mad:....enough to make a Marine blush..:eek:..but..
    466584
    Had one of these that was a hair too fat....hammer assist got most of it into...
  11. Tablesaw to remove the waste. Getting the last...

    Tablesaw to remove the waste. Getting the last of these splines fitted up...
    466555
    Almost there....and..
    466557
    Last ones....needed grooves milled to house the panel for the bottom (floor?) of...
  12. Replies
    15
    Views
    1,334

    Hmmm.. 466524 This one is just sitting around,...

    Hmmm..
    466524
    This one is just sitting around, doing nothing....since I already have a pair of T-19s in the tool cabinet...

    Has a few patent dates on the back porch.....tote has been...
  13. We now have a pattern to work with... 466508...

    We now have a pattern to work with...
    466508
    Have to work on getting rid of the tear-out....mainly from cutting the double bead....
    466509
    Maybe a different wood?
    466510
    These are the insides...
  14. Replies
    15
    Views
    1,334

    Next time..stop by the Dungeon Shop....and we...

    Next time..stop by the Dungeon Shop....and we will talk about it....

    Shop is almost always open for visitors....
  15. One...foam floor pads under the feet of the...

    One...foam floor pads under the feet of the bench, to isolate it from the floor. 2, play music as you work....and time the mallet blows to the drums.
  16. Joinery, Part 1. Means I need to set up the...

    Joinery, Part 1. Means I need to set up the Zero Clearance Overlay...and set up the tablesaw to plough a groove into the end grain...about..8 grooves all total...
    466436
    trying to center a 1/4"...
  17. Yesterday...had a quilt needing washed and...

    Yesterday...had a quilt needing washed and dried..so, 2 trips down to the shop...one to start the washer with the quilt....then bring a plank down the steps to the shop....
    466429
    All 6' 4" of...
  18. Jewelry Box, with Fancy Corner Joints

    After almost 6 weeks on the Injured Reserve....finally am able to return to the shop....at least on a limited basis....letting the knee decide when I am done. Anyway..while enjoying a nice,...
  19. So...I need a door to cover the cubbies...might...

    So...I need a door to cover the cubbies...might have a few scraps laying around...
    466390
    Some Mortise and tenon corner joints....mill a slot for a plywood panel...
    466391
    5 piece of wood, a few...
  20. There was also a very fancy bench he made...

    There was also a very fancy bench he made...
  21. Hmmm...offset dados? 466320 Where 2 shelves...

    Hmmm...offset dados?
    466320
    Where 2 shelves meet....have to off set just a bit, otherwise won't be much left in the divider....Bracket is to attach the hutch to the desk.
    Shelves in the cubby...
  22. That business ( Funny Business?) with posting...

    That business ( Funny Business?) with posting photos......especially when I am sure when this build thread was first seen on this site, those photos did NOT have any issues. Anyway, I'll try again,...
  23. Hmm...Photos have a mind of their own, it would...

    Hmm...Photos have a mind of their own, it would seem....and this site won't let me FIX/EDIT to what I intended?

    Assembly was pretty straight forward...just a drawer..
    466179
    Then stash in...
  24. "Skinny Drawers"? No, not skinny jeans....the 2...

    "Skinny Drawers"? No, not skinny jeans....the 2 drawers that will be over my legs.....
    466159
    They both have to fit in there....rather a bit shallow, not meant to hold all that much....so....
  25. Replies
    14
    Views
    957

    Just as about every town or village had a...

    Just as about every town or village had a Blacksmith's Shop...there was also at least one Joiner working in the area. Buildings were done during the summer's good weather. After the Fall's...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4