Search:

Type: Posts; User: Bill Wyko; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.53 seconds.

  1. Replies
    8
    Views
    797

    Everything is end grain including the border so...

    Everything is end grain including the border so expansion shouldn't be an issue. It is essential to keep them oiled.
  2. Replies
    8
    Views
    797

    Another dizzying design cutting board.

    I'm at it again, Another 3D end grain cutting board. 416342
  3. Thanks, these actually are endgrain and extremely...

    Thanks, these actually are endgrain and extremely stable. Takes a ton of wood to make them.
  4. Replies
    15
    Views
    1,609

    If you want to get creative, you could cut it...

    If you want to get creative, you could cut it into strips about 1.25 thick, turn them up 90 degrees, glue them back together and make it an end grain cutting board. That way you almost never see a...
  5. You should see what it takes to keep everything...

    You should see what it takes to keep everything lined up, that will bang your eyeballs into each other.
  6. I use masking tape to hold everything while I...

    I use masking tape to hold everything while I carefully apply pressure with the clamps.
  7. What do you think is the best rolling base for heavy tools?

    I have a Baileigh 25" surface sander on the way and I need a rolling base for it. it measures 41 x 12.5 at the base. It weighs around 600 lbs. I would like it to fit the base, not one size fits all...
  8. A couple cutting boards to get sucked into.

    So I'm not back to full capacity yet but I've made time to make a few cutting boards recently. Please enjoy.
  9. Replies
    11
    Views
    1,348

    Eventually I want to turn a platter using one of...

    Eventually I want to turn a platter using one of these on my lathe.
  10. Replies
    11
    Views
    1,348

    Thanks everyone, the border is Cocobola, hard...

    Thanks everyone, the border is Cocobola, hard Maple and Jatoba. Been using it for a few weeks now and not a trace of a mark anywhere.
  11. Replies
    11
    Views
    1,348

    Dizzying cutting board

    So I've taken up cutting boards as a new way to express myself. Over 400 pieces, made of Jatoba, hard Maple and Cocobola. Please enjoy.
  12. Replies
    3
    Views
    482

    hey had a video of exactly what I want to do,...

    hey had a video of exactly what I want to do, thanks again.
  13. Replies
    3
    Views
    482

    Thanks very much, going there now.

    Thanks very much, going there now.
  14. Replies
    3
    Views
    482

    Traditional finish on a Morris chair

    I plan on building some Morris style furniture, what would be the traditional style finish and the best method for application?
  15. Replies
    7
    Views
    652

    Thanks, it gets delivered tomorrow. I'm going to...

    Thanks, it gets delivered tomorrow. I'm going to start with a Morris chair, end table, coffee table and a sofa I'm going to design.
  16. Replies
    7
    Views
    652

    Leigh FMT PRO questions

    So I just ordered a used FMT Pro. It's an older one so I've found one upgrade, the piece that your wood rests against. Does anyone know of any other upgrades other than the numerous guides.
  17. Replies
    45
    Views
    12,800

    Just checking to see if you are still around and...

    Just checking to see if you are still around and if you have anything more to share.
  18. Replies
    12
    Views
    2,293

    BTW Scott, you know the old saying, if it doesn't...

    BTW Scott, you know the old saying, if it doesn't hold water, it must be art. 8-) That's one fine piece of art my friend.
  19. Replies
    41
    Views
    7,051

    I would also like to point out something I just...

    I would also like to point out something I just recently discovered, i find that when sharpening on a flat surfaced sharpener, my gouge seems to keep its sharp edge much longer. It also seems to feel...
  20. Replies
    14
    Views
    3,454

    And your first step off the slippery slope into...

    And your first step off the slippery slope into the vortex begins, congratulations
  21. Replies
    11
    Views
    3,418

    No one mentioned its ability to be used as a...

    No one mentioned its ability to be used as a rotary tool as well. I was deciding between a foredom & the Jooltool. I figured I get a sharpener with my rotary tool. I need it to do more spiral work in...
  22. Replies
    11
    Views
    3,418

    I'm surprised at how fine a finish I can get on...

    I'm surprised at how fine a finish I can get on it. The real test will be when I turn something segmented. We'll see if any glue loads up around the gouge. Something kind of funny happened though, a...
  23. Replies
    24
    Views
    4,592

    I just purchased a Jool Tool sharpening system so...

    I just purchased a Jool Tool sharpening system so now my Glaser Synergy gouge is sharpened on a flat plane vs the curve of my wet sharpener. i have to say, my gouge seems to hold an edge much, much...
  24. Replies
    4
    Views
    1,281

    Look into inlace, it's a simulate but doesn't...

    Look into inlace, it's a simulate but doesn't damage your tool edge.
  25. Replies
    11
    Views
    3,418

    Jool Tool sharpening system

    While I was at the AAW symposium, I saw a demo being done by a woman named Anie, she is the owner of Jooltool. At first I was a little skeptical but after standing there and seeing for my own eyes...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4