Search:

Type: Posts; User: Chris Rosenberger; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    39
    Views
    23,098

    Maybe it is wrong in the state you live in. An...

    Maybe it is wrong in the state you live in.
    An electrician did all of the wiring in my shop.
  2. Replies
    2
    Views
    1,339

    Delta 31-484 Spindle Sander

    When Delta brought out the 31-484 spindle sander, I was very interested except for the price.
    I noticed recently that several dealers have dropped the price of the sander by several hundred dollars,...
  3. Thank you Frank. I was going to order one until I...

    Thank you Frank. I was going to order one until I noticed that. I do all of my measuring from left to right. Can't do that with this rule.
  4. The only changes that need to be made in the...

    The only changes that need to be made in the starter is move the wire on the transformer to the 230 volt pole (done) & change the 3 overload heaters to something close to 20 amp. The overload block...
  5. Replies
    4
    Views
    1,177

    Depending on the age & kind of saw, you replace...

    Depending on the age & kind of saw, you replace the arbor with a new one. Another option is to take it to a machine shop to see if they could repair it.
  6. It would help me in for setting my hollow chisel...

    It would help me in for setting my hollow chisel mortiser. Right now I do a trial & error process to center the chisel.
    With the Woodpecker jig, just mark the location of the centered mortise, set...
  7. It says on the bars "For use with pencils &...

    It says on the bars "For use with pencils & knives Made in the U. S. A."
    Those might be hard to find. :D

    If you layout a lot of mortises & tenons & need to find the centers of board edges, this...
  8. Replies
    8
    Views
    3,834

    Below is a picture of the mounting base I...

    Below is a picture of the mounting base I originally made for a Incra Ultra jig to use on a table saw with a 52" Unifence. I would use the Incra Jig as the table saw fence when I needed to do a lot...
  9. Replies
    3
    Views
    762

    Are you looking for a stock replacement guard or...

    Are you looking for a stock replacement guard or an after market guard?

    I like the Biesemeyer overarm guards myself.
  10. Replies
    39
    Views
    23,098

    Like some of the others, we just used junction...

    Like some of the others, we just used junction boxes & covers. We cut holes in the covers & used standard box connectors.
    We have several around the shop. Many of them have been in use for over 20...
  11. Replies
    9
    Views
    2,120

    I have the Incra LS52-TS on one of my table saws....

    I have the Incra LS52-TS on one of my table saws.

    I like it very much. I really like being able to come back to same measurement over & over again with out remeasuring. I also like being able to...
  12. Replies
    11
    Views
    1,955

    The fence has a T slot on the front. It is very...

    The fence has a T slot on the front. It is very easy to attach jigs to it.
  13. Replies
    11
    Views
    1,955

    The 1000 SE is an excellent miter gauge, although...

    The 1000 SE is an excellent miter gauge, although I like the 1000 HD even better. I use both.
  14. Replies
    12
    Views
    2,226

    It could just be that the potential buyers at...

    It could just be that the potential buyers at those types of auctions have lots & lots of money. They did not get all that money by making snap decisions, so the auctioneer has to go slower to give...
  15. I use any flat surface I have available at the...

    I use any flat surface I have available at the time & 2 pieces of 1 1/2" x 2' x 8' foam insulation.
  16. Replies
    20
    Views
    3,225

    A simple way to get the same result, would be to...

    A simple way to get the same result, would be to use a regular mobile base & 4 wedges.
    Park the jointer where you are going to use it & lightly drive a wedge under each corner.
    When you need to...
  17. I use the tilt method, but I do not use 2 x 4s. I...

    I use the tilt method, but I do not use 2 x 4s. I set the mobile base next to the machine on the side I can raise the highest & can get the best grip. For a table saw with a wide rip fence & I do not...
  18. Replies
    12
    Views
    2,226

    If you had ever attended an auction where a non...

    If you had ever attended an auction where a non auctioneer did an auction you would know why.

    I recently attended a charity auction that had a non auctioneer sell the items. Things went dirt...
  19. Replies
    7
    Views
    4,631

    I do not have the Kreg K5, but this should work...

    I do not have the Kreg K5, but this should work the same on all Kreg jigs. To use a longer screw, all you need to do is lower the stop collar on the drill bit so the hole is not drilled as deep. The...
  20. I do not have my Kapex setup in the shop, but...

    I do not have my Kapex setup in the shop, but this is how I have my Dewalt setup.

    http://i123.photobucket.com/albums/o303/chrisrosenb/Shop%20Album/DSCF1760.jpg

    ...
  21. Replies
    7
    Views
    1,592

    You did good Troy.

    You did good Troy.
  22. Replies
    8
    Views
    10,595

    Is the magnetic starter in a plastic box on the...

    Is the magnetic starter in a plastic box on the front of your saw, or in a metal box on the back of your saw?
  23. It looks like a bad machining job. I have not...

    It looks like a bad machining job. I have not seen an arbor set screw that far off center of the flat spot. Your set screw is at the edge of the flat spot.
    That still does not mean that the arbor...
  24. Replies
    5
    Views
    1,570

    John, thanks for the information. I had not seen...

    John, thanks for the information. I had not seen that before.
    I am not sure I see the point of doing them that way.
  25. Doug, You misunderstood the reaming. We were...

    Doug,

    You misunderstood the reaming. We were talking about reaming the top mounting holes, not the arbor bearing hole.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4