Search:

Type: Posts; User: Bill Orbine; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Kilz is fine! You will not have a bleed problem...

    Kilz is fine! You will not have a bleed problem with poplar. Yes, you'll have to "fill" the grain in the bendable luan as stated before.
  2. Replies
    41
    Views
    6,467

    I have my eye on buying a couple of Rigids from...

    I have my eye on buying a couple of Rigids from Home Depot at 50 buck each in the near future. They look to be well made with easy adjustable height and has a 2x4 (supplied) cross that I don't...
  3. Replies
    5
    Views
    746

    More likely a wet dream (Not pratical): ...

    More likely a wet dream (Not pratical): ...
  4. Replies
    64
    Views
    12,007

    Red stuff on the shaft behind pulley appears to...

    Red stuff on the shaft behind pulley appears to be Loctite or some kind of adhesive? With no mechanical fastener on the pulley, perhaps the adhesive to "fasten" pulley was used . Use a puller...
  5. Yeah... this is the forum where we are not...

    Yeah... this is the forum where we are not allowed to say........ but the gloaters still keep on gloating! Free is nice!
  6. Replies
    34
    Views
    8,008

    I often get the ones with the wobble wheels!

    I often get the ones with the wobble wheels!
  7. Replies
    24
    Views
    4,950

    Mcmaster-Carr has .625 drill guides of many...

    Mcmaster-Carr has .625 drill guides of many various sorts.... perhaps you can make your own doweling jig with their products.
  8. For eight trim pieces, cut all the miters one end...

    For eight trim pieces, cut all the miters one end leaving each piece slightly longer in length for the other end to be mitered later. Mark all eight pieces for the fit as well as to which sides, top...
  9. Replies
    37
    Views
    11,953

    Maybe you ought to mount your toilet on the...

    Maybe you ought to mount your toilet on the kitchen sink......:D
  10. My opinion is the panel problem is more of a...

    My opinion is the panel problem is more of a manufacture defect. It is common for panel to shift by seasonal expansion and shrinkage. I can see that the panel bevel in the corner out of alignment...
  11. Replies
    13
    Views
    5,497

    The corner cabinet does not need to be the full...

    The corner cabinet does not need to be the full 24" deep.... so making it slightly shallower (about 1/2-3/4") can help compensate somewhat for the OOS walls. Since delivery isn't the major issue,...
  12. Replies
    65
    Views
    12,232

    Grass....every week in the summer I gotta cut...

    Grass....every week in the summer I gotta cut it!:rolleyes:
  13. Replies
    7
    Views
    1,771

    For some reason I thinking this jointer is...

    For some reason I thinking this jointer is neither Rockwell nor Powermatic. The thing is.... The the locking knobs is on the backside of the jointer which I don't see on either one of the old...
  14. Replies
    11
    Views
    2,761

    I'm with the metal roof concept...... It would be...

    I'm with the metal roof concept...... It would be wise to check with local codes.
  15. Replies
    53
    Views
    6,329

    So, maybe your theif was a cop?:rolleyes:

    So, maybe your theif was a cop?:rolleyes:
  16. Replies
    34
    Views
    3,966

    Holes in Lifesavers..... Remember the promotion...

    Holes in Lifesavers..... Remember the promotion that they were later selling the holes?
    Ice Cream use to be sold in pint, quart and 1/2 gallon.
  17. Replies
    9
    Views
    1,812

    A lot of stuff follows me home except money.........

    A lot of stuff follows me home except money......

    Never seen a State T5! More pics when you have it set up!
  18. I have the Tops! Smooth rider and accurate cuts....

    I have the Tops! Smooth rider and accurate cuts. Set up for square cuts and very rarely use it for anything other than cross cuts. In the 20 plus year I've use this saw, I can't remember it ever...
  19. Replies
    21
    Views
    3,626

    Just wondering if the new motor is turning the...

    Just wondering if the new motor is turning the right direction......???????
  20. Replies
    17
    Views
    2,691

    I've done well with Ram Board. It's a roll of...

    I've done well with Ram Board. It's a roll of cardboard material. I can get it at the local yard or the Borg. Tape the perimeter and seams. Optional: Plastic or rosin paper underneath.
  21. Replies
    13
    Views
    2,987

    The rap on the side of collet nut with wrench is...

    The rap on the side of collet nut with wrench is typical for PC routers to loosen router bit after the nut has been loosened.
  22. Replies
    13
    Views
    4,595

    You could take your mason jar to a glass place...

    You could take your mason jar to a glass place and..... might be cheaper and efficient!
  23. Replies
    33
    Views
    4,514

    As it has been said before....45 degree cut -...

    As it has been said before....45 degree cut - done! Not good enuff? OK... Find come soup, coffee, paint or whatever can that might come close to the radius on the truck bed to trace a radius. But...
  24. Replies
    9
    Views
    1,758

    Pressure wash the darken pavers might work.

    Pressure wash the darken pavers might work.
  25. If you had changed the knives (as you stated),...

    If you had changed the knives (as you stated), you are missing something... You need to make sure all your knives meet the outfeed table at TDC.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4