Search:

Type: Posts; User: Paul Mattaliano; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.22 seconds.

  1. For those keeping score, building the plinth out...

    For those keeping score, building the plinth out of square resulted in a nice even reveal between the plinth and the cove molding. Glad this one is done.
    405024
  2. Replies
    18
    Views
    2,670

    I get Sunday only Chicago tribune. They do the...

    I get Sunday only Chicago tribune. They do the same thing with reducing subscription period based on cost of those special editions. In the past I ignored it, figured it was legit. Then I started...
  3. Well, I attempted tapering the plinth on the...

    Well, I attempted tapering the plinth on the jointer and that didn’t go so well. The end grain of the tails, tall pieces with narrow strips connecting the feet so it’s tough to properly support it,...
  4. How would this be done on the jointer? I need to...

    How would this be done on the jointer? I need to take about 1/16 off one end and taper to nothing off the other end.


    The area above the cutouts in the plinth is 3/4" thick x ~1" wide. It seems...
  5. It’s about 1/16” difference between front and...

    It’s about 1/16” difference between front and back reveals.

    Not sure about my hand tool skills and planing the plinth.

    I thought about tapering the molding but it seemed to me that that would...
  6. Sweet parallelogram....or how do you hide out of square

    Evening, all. Working on this blanket chest and I didn't get the case quite square. You'd never know by looking at it until the molding is attached.

    THe plan was to build the plinth so that it...
  7. the arbor bearing?

    the arbor bearing?
  8. correct but once the filter is on, how do you get...

    correct but once the filter is on, how do you get the lower bag on with the ring? you need access to the inside of the bag to install/remove the ring.

    if I were an octopus with opposable thumbs...
  9. for those with the Wynn filter on a Delta 50-760

    if you're attaching the filter with turnbuckles on the inside, how do you use the felt ring on the inside to attach the bag? I see photos of people doing but just don't get it -- once you attach the...
  10. 279043 If your dc has a 5" input you can use one...

    279043
    If your dc has a 5" input you can use one of these with a hose coupler/connector
  11. Replies
    6
    Views
    1,497

    Thanks for the feedback. Rough overall dimensions...

    Thanks for the feedback. Rough overall dimensions on the base cabinet are 40" wide x 18" deep x 36" high. Top is 12" deep x 42" high (overall height 78").

    The shelves will be adjustable. I...
  12. Replies
    6
    Views
    1,497

    design review

    278636278637278638
    just throwing this up for any constructive comments/criticism on this design (proportions, etc.). The plan is for the top to be a bookcase and the bottom to hold miscellaneous...
  13. Replies
    7
    Views
    2,551

    It is but I did change the cabinet section from 6...

    It is but I did change the cabinet section from 6 shallow drawers to 2 deeper drawers plus the cabinet doors. I also reduced the overall height a little to match the tablesaw height.
  14. Replies
    7
    Views
    2,551

    dual purpose table saw outfeed table

    it also functions as a workbench
  15. please add me; thank you!

    please add me; thank you!
  16. Replies
    352
    Views
    51,300

    Add me please. Thank you.

    Add me please. Thank you.
  17. please add me. Thank you!

    please add me. Thank you!
  18. please add me. Thanks!

    please add me. Thanks!
  19. please add me. Thank you!

    please add me. Thank you!
  20. please add me. Thank you!

    please add me. Thank you!
  21. please add me. Thank you!

    please add me. Thank you!
  22. please add me. Thank you!

    please add me. Thank you!
  23. Please add me. Thank you

    Please add me. Thank you
  24. question for those with G0555x and riser block

    I just bought this saw and set it up without the riser block as the block was on back order. Everything worked great. Finally got the block and got it installed but I can't get the supplied 105"...
  25. Replies
    3
    Views
    4,645

    non-mortise hinges and back bevel

    I have 1 inset cabinet door to fit and in checking out NM hinges at Horton Brasses, they indicate to back bevel the doors 2-3 degrees. Can someone tell me what the purpose of this back bevel is and...
Results 1 to 25 of 46
Page 1 of 2 1 2