Search:

Type: Posts; User: Greg Parrish; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. looking at this also. my new lenovo c940 has 4k...

    looking at this also. my new lenovo c940 has 4k and i bought an LG 27" 4k monitor and a thunderbolt 3 dock rated at up to 8k via display port 1.4 but havent received the dock yet. are you guys...
  2. Replies
    6
    Views
    366

    Part of the issue I’ve run into is that my CNC...

    Part of the issue I’ve run into is that my CNC sits a good bit higher than my Felder sliding saw. Every spot I was initially thinking about creates an issue when looking at how it interacts with...
  3. Replies
    6
    Views
    366

    That small toolbox won’t be there but you are...

    That small toolbox won’t be there but you are right that I’m tight on space. Only 440 sq ft and a golf cart sits in a big chunk of that except when I pull it out to work. But it has to have room to...
  4. Replies
    6
    Views
    366

    Workbench spacing and clearances ?

    Due to acquiring a CNC last week, Im forced to give the workbenches spot to the CNC so that the rest of the room clearances work for the saw and jointer/planer. That said, its not the most ideal...
  5. Replies
    38
    Views
    1,817

    I purchased and downloaded VCarve Pro in the last...

    I purchased and downloaded VCarve Pro in the last few days and started watching their getting started videos. They look very helpful. I was watching on my iPad and following on my laptop. Hoping to...
  6. Replies
    22
    Views
    887

    and it’s usually in stock and ready to ship as...

    and it’s usually in stock and ready to ship as opposed to the new Millright unit that is coming. I almost ordered a Shapeoko XL before finding my used Axiom last week. It would have been a little...
  7. Replies
    9
    Views
    370

    I have one of the grizzly overarm deals that I...

    I have one of the grizzly overarm deals that I converted to hang from the ceiling. It uses a 3” hose and like you mentioned with my Oneida dust collector suction is very strong. In fact if I’m doing...
  8. Replies
    10
    Views
    492

    Not to thread jack but BLO is a recommended...

    Not to thread jack but BLO is a recommended finish for work benches? The maple bench I bought from Benchcrafted is unfinished and has seasoned in my shop for 6 months or so now. I’m thinking it...
  9. Replies
    22
    Views
    887

    that was the same for me. When looking at a parts...

    that was the same for me. When looking at a parts build the cost ends up way more than the prebuilt models in the 2x3 and 2x4 size I was looking at.
  10. I don’t have them but like the looks of them...

    I don’t have them but like the looks of them compared to the little brass set I have from Rockler. The size appeals to me as the brass ones are very small. But I won’t be buying them at that price...
  11. I’m using the powertec 3” from amazon on mine and...

    I’m using the powertec 3” from amazon on mine and it works fine.
  12. Replies
    72
    Views
    3,191

    slid the machine onto the stand with help of some...

    slid the machine onto the stand with help of some 2x4’s and my family spotting me here and there.
    417669

    everything cleaned and dusted and assembled (not sure why pictures rotated. Sorry)...
  13. Replies
    72
    Views
    3,191

    Boy am I pooped but after 9 hours driving and a...

    Boy am I pooped but after 9 hours driving and a few hours of sweat equity, the CNC is bought, transported and unloaded. Tomorrow will have to start the reassembly process as Im too tired to do it...
  14. Replies
    72
    Views
    3,191

    I was already thinking of lowering it for...

    I was already thinking of lowering it for clearance but that is a good idea also. It is supposed to be setup for me to test when we get there. I’ll have to look for some foam to put in the car....
  15. Replies
    72
    Views
    3,191

    Will do. I’m taking an assortment of tools and...

    Will do. I’m taking an assortment of tools and items to better help with what we need to do to make it fit and to get it loaded. Also including items like duct tape, ratchet straps, rope, etc. will...
  16. Replies
    72
    Views
    3,191

    I think so. I have one reserved to pick up...

    I think so. I have one reserved to pick up tonight. Will measure and see
  17. Replies
    72
    Views
    3,191

    Well if I rent the suburban I’m not allowed to...

    Well if I rent the suburban I’m not allowed to tow per rental car companies (if it has a hitch). The measurements/specs point to it fitting. If I don’t then I’ll be using my ford fusion and trailer. ...
  18. Replies
    72
    Views
    3,191

    Any reason to think I won’t be able to get the...

    Any reason to think I won’t be able to get the axiom pro 6 in the back of a suburban with the rear seats all down if removed from the stand? Thinking it would be safer than bouncing around on my...
  19. I ended up exchanging the HP unopened and picking...

    I ended up exchanging the HP unopened and picking up an open box Dell Inspiron 15 7000 with better specs for less than the cost of upgrading the memory in the HP. This one has a 15.6" 4k screen,...
  20. Replies
    26
    Views
    1,238

    Mine is a kobalt 4 sensor model from Lowes that...

    Mine is a kobalt 4 sensor model from Lowes that works great. It is a predecessor to the current model they sell. At the time I bought it, it seemed comparable in spec and user review to those from...
  21. Sounds like this one will work just fine then....

    Sounds like this one will work just fine then. Only thing I may do is add another 8 gig memory stick. Thanks guys.
  22. Thanks Jim. If I’m understanding what I’m...

    Thanks Jim. If I’m understanding what I’m reading, unlike when I bought my last computer, today the laptop cpus are rated at a base level and the software increases their performance as needed. The...
  23. I’m Sorry to say that I don’t know how to...

    I’m Sorry to say that I don’t know how to interpret that.

    Your gigz speed is higher. But I’m guessing the processor is older. So does that mean the one I pictured will work or is a higher gigz...
  24. There website says minimum requirement is a 2...

    There website says minimum requirement is a 2 gigahertz or higher multicore processor. Is that true? Would this computer work well or should I push further up to a higher megahertz processor?
    ...
  25. One more question. Any benefit to one...

    One more question.

    Any benefit to one direction or the other processor wise between an i5 10210U 10th gen intel versus a Ryzen 5 3500U 2nd gen AMD.

    Im thinking about going with a 14” laptop...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4