Search:

Type: Posts; User: Prashun Patel; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.60 seconds.

  1. Replies
    33
    Views
    3,080

    I've been spraying Target products with a Fuji...

    I've been spraying Target products with a Fuji Semi Pro 2 for a couple years, and now a Q4. Either are fine. The gun/cup for the Q4 are better than the SP2.

    I would choose a turbine system...
  2. Off the planer, 150. These days, I try to...

    Off the planer, 150.

    These days, I try to choose my wood carefully and as straight grained as possible. Costs more, takes more up front time. Makes the rest of the process enjoyable.
  3. Replies
    20
    Views
    688

    Good luck with that. I bet it only works on the...

    Good luck with that. I bet it only works on the smallest and split-proniest of woods.
  4. That being said I had no trouble with it on my q4...

    That being said I had no trouble with it on my q4 with the stick tip.

    (Edit). Oops I mean stock tip.
  5. You don't need a bandsaw. But it's a very...

    You don't need a bandsaw. But it's a very versatile tool for the space it takes up.

    If you turning anything from bowls to spindles, a bandsaw is a great 7 iron to the chainsaw's driver and...
  6. Be proud. It's looking great. I rish you...

    Be proud. It's looking great. I rish you continued success.
  7. Replies
    21
    Views
    1,138

    Where in PA? If you are near Kesey, contact...

    Where in PA? If you are near Kesey, contact Pete Terbovich at Horizon. They will likely have an ok supply of curly maple. They will likely have an outstanding supply of curly cherry if you want...
  8. Target will match any color from the major paint...

    Target will match any color from the major paint manufacturers in their EM6500 tinted lacquer. I did my son's bathroom cabinets in a Benjamin Moore blue this way.

    I topcoated with EM8000cv with...
  9. It can happen even on a wheel without...

    It can happen even on a wheel without imperfections like a cbn too.
  10. The issue for me was that repeated grindings with...

    The issue for me was that repeated grindings with the v arm set at one place caused the bevel to contact imperceptibly lower each time. Itís fine at first when I was well above center.

    But...
  11. My SRG doesn't have swept back wings by design. ...

    My SRG doesn't have swept back wings by design. It's never been an issue. I used to sharpen on a v arm until I learned the hard way why this is dangerous. I now sharpen on a flat tool rest.
  12. Replies
    34
    Views
    2,548

    I have noticed a lot of busking recently. I seem...

    I have noticed a lot of busking recently. I seem to see a lot of saxophonists though.

    Seems like every corner in my town has a CVS or Walgreens and a busking musician.

    Too much sax, drugs,...
  13. Replies
    10
    Views
    1,316

    It's not hard to build. This part was free. The...

    It's not hard to build. This part was free. The tail stock centers and holds it just fine.
    I got a magnetic counter for maybe $20 that works just fine. The magnet embeds in the edge of the disc. ...
  14. Have you tested lacquer on the bare wood, no...

    Have you tested lacquer on the bare wood, no filler, no shellac, no stain.

    It is possible you just have bad lacquer that is not drying.

    The soft finish problem can also happen because the...
  15. Replies
    10
    Views
    1,316

    Iím only doing this with my son so we can learn...

    Iím only doing this with my son so we can learn how pickups work.

    Iíve made a wood plate that I will screw the housing to (as you suggest). I got a counter too. Will have to figure out how...
  16. Um, I wouldn't finished in a sealed basement. ...

    Um, I wouldn't finished in a sealed basement. You should still have a way to vent the fumes. The solvents used in any of these finishes are not SAFE, just not VOLATILE (which is an arbitrary...
  17. Replies
    10
    Views
    1,316

    Guitar pickup winder

    Has anyone made a faceplate pickup winder for your lathe? Iím looking for a quick and dirty way to mount, wind, and count the coils.
  18. Replies
    30
    Views
    2,449

    If it were me: No.6: No need to get the whole...

    If it were me: No.6: No need to get the whole bevel to 25. Use 25 as the micro bevel. Over months/years, you'll grind it back completely as you resharpen.

    For the No. 7, I'd buy a new blade. ...
  19. Replies
    14
    Views
    1,206

    I'd skip the seal a cell. I had the best luck...

    I'd skip the seal a cell. I had the best luck with Arm R Seal or any wiping varnish by using semi gloss or satin.
  20. Replies
    39
    Views
    2,739

    not at ALL. It should not be sloppy. I would...

    not at ALL. It should not be sloppy. I would contact Festool. I suspect they may help you.
  21. Replies
    39
    Views
    2,739

    How thick are your pieces? Can you take some...

    How thick are your pieces? Can you take some photos? It should not be consistently off like this. And 2mm is way too much. Mine are sometimes off but less than 1mm. Itís usually because...
  22. Replies
    14
    Views
    837

    That is highly prized wood there. I got a ton...

    That is highly prized wood there.

    I got a ton of flame box elder a few years ago and it is some of the best wood I've turned. It's dramatic (you have awesome coloring there) and there is nothing...
  23. Robert, How are GTechniq or Gyeon applied?

    Robert, How are GTechniq or Gyeon applied?
  24. These aren't that cheap; so I'd like to protect...

    These aren't that cheap; so I'd like to protect them. They're heavy and bulky enough that I can't store them in the garage. I think I just need to invest in covers.
  25. Plastic Resin Patio Furniture UV protectant?

    Does anyone have a recommendation for an HVLP sprayable product I can apply to plastic resin chairs? They're brightly colored. I will cover them, but would also like to treat them.

    John T? Jim?...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4