Search:

Type: Posts; User: Mark Rainey; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    5
    Views
    454

    Good job Stewie. I have the Lie Nielsen...

    Good job Stewie. I have the Lie Nielsen reproduction as well as the Veritas R and L hand version. I do like the 95.
  2. Replies
    20
    Views
    1,736

    I hear you Phil. Actually 42 by 60 ain't that...

    I hear you Phil. Actually 42 by 60 ain't that small. I could see how that would be challenging. I think Warren commented on maple in a previous post, saying that it is a very challenging wood to...
  3. My money is on Charles' deduction. ;)

    My money is on Charles' deduction. ;)
  4. Replies
    27
    Views
    1,708

    Jeff, the walnut chair is a winner! Impressive...

    Jeff, the walnut chair is a winner! Impressive work.
  5. Replies
    18
    Views
    1,258

    I heard back from Lee Valley. They recommend...

    I heard back from Lee Valley. They recommend grinding a flat in the drill bit, as Doug & Bill recommend. They said some drill bits have a flat already ground. I will try this approach. The Amana...
  6. Replies
    18
    Views
    1,258

    [QUOTE=johnny means;3122604]It's an inherently...

    [QUOTE=johnny means;3122604]It's an inherently flawed design. I switched to these years ago have never had any problems.[/QUOTE

    Johnny, who makes these?
  7. Replies
    18
    Views
    1,258

    I will try that Edwin. Very frustrating when you...

    I will try that Edwin. Very frustrating when you have the drill bit tight in the chuck, the hole drilled, but the counterbore standing still not drilling.
  8. Replies
    18
    Views
    1,258

    Bill, those flats on the shaft are nice. As Doug...

    Bill, those flats on the shaft are nice. As Doug said I may have to grind on myself.
  9. Replies
    47
    Views
    6,912

    Looking forward to your progress. Good things...

    Looking forward to your progress. Good things take time Chris!
  10. Replies
    11
    Views
    934

    Thanks Julian. I am using 100% heartwood cherry....

    Thanks Julian. I am using 100% heartwood cherry. I am optimistic it will hold up. The legs are bent laminations of 8 pieces of slightly less than 1/8 inch cherry resawed from a thicker board. At...
  11. Replies
    18
    Views
    1,258

    Thanks Doug, this may be the solution. I will...

    Thanks Doug, this may be the solution. I will call Lee Valley and follow up.
  12. Replies
    18
    Views
    1,258

    The counterbores do come with the drill bits. ...

    The counterbores do come with the drill bits. And I also used the counterbore on a brad point drill bit from LV.

    458328458329458330458331
  13. Replies
    11
    Views
    934

    Lowell, cypress, white oak, cedar, hemlock and...

    Lowell, cypress, white oak, cedar, hemlock and mahogany are good choices. I was afraid white oak would be a bit heavy and difficult to work with hand tools. I have a good supplier of cherry and...
  14. Replies
    18
    Views
    1,258

    Lee Valley counterbore countersink set

    Got Lee Valley counter bore/ countersink set 6 months ago. They have been working good, but of late, the counterbore/sink collet that goes over the drill bit has been slipping and spinning. I...
  15. Replies
    17
    Views
    1,141

    Check out this...

    Check out this
  16. I would buy a quality new saw set for $75.

    I would buy a quality new saw set for $75.
  17. Replies
    13
    Views
    1,439

    Walnut is impressive. Custom fit to his...

    Walnut is impressive. Custom fit to his environment - now that is a personal touch!
  18. Stub tenon should be 1/2 to 3/4 inches. No need...

    Stub tenon should be 1/2 to 3/4 inches. No need for longer - this is not a glue dependent joint. One bed bolt only fir each post. And only 4 bed bolts needed - 6 inches would be nice.
  19. Replies
    17
    Views
    2,744

    Joel, you nailed it! I like the continuous grain...

    Joel, you nailed it! I like the continuous grain that runs across the top drawers. I like everything about it!
  20. Replies
    23
    Views
    1,943

    It is possible John. The same problem happened...

    It is possible John. The same problem happened with both new 3/4 inch Resaw King blades.
  21. Replies
    23
    Views
    1,943

    Yes David, I think our machines are very similar....

    Yes David, I think our machines are very similar. It just seems when I put full tension on the 3/4 inch blade it seems like it is different positions on the upper and lower wheels, and looks odd to...
  22. Replies
    23
    Views
    1,943

    Thanks for the info John. I tried to get the max...

    Thanks for the info John. I tried to get the max tension my Rikon 14 inch could give. Maybe it is just not enough. I futzed around with John White's method for measuring tension from a fine...
  23. Mike, that looks like a nice table. I do not...

    Mike, that looks like a nice table. I do not think the lumber you get from Home Depot will work best. The lumber may not be the quality you want ( knots and warp ) and the moisture content will be...
  24. Replies
    23
    Views
    1,943

    Thanks for the advice Chris.

    Thanks for the advice Chris.
  25. You should be fine. I note Roger also mentioned...

    You should be fine. I note Roger also mentioned a stub tenon. Less chance for break out of the bolt.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4