Search:

Type: Posts; User: Lee Schierer; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 2.01 seconds.

  1. Two more very likely cause for the teeth marks...

    Two more very likely cause for the teeth marks and the burning. The blade in use has too many teeth. A ripping type blade with fewer teeth would work better. If the blade doesn't want to make full...
  2. As mentioned above, I spent some time in...

    As mentioned above, I spent some time in California recently specifically to see the redwood trees. We had visited California a few years ago and saw the Sequoia trees. According to the National...
  3. We were recently in northern California and we...

    We were recently in northern California and we did see burned areas where they were harvesting the large trees along the road and we saw trucks hauling logs in other areas that showed signs of recent...
  4. Aad a piece of 3/4 x 3/4 stock across the front...

    Aad a piece of 3/4 x 3/4 stock across the front under the drawers so that it runs from the leg on the left to the leg on the right and attach it to the blocks in between the drawers. It will act...
  5. You don't indicate how long the table is going to...

    You don't indicate how long the table is going to be. By making the drawers a bit shallower, you can run a rail all the way across, attached to the back of the spacers between the drawers, which...
  6. Replies
    12
    Views
    501

    This is where some high school math, i.e. ratios...

    This is where some high school math, i.e. ratios will help you out. Lets say they give you the over all dimensions of the cabinet as 24 wide, 14 deep and 32 high, but the drawing is on a standard...
  7. Replies
    20
    Views
    959

    My router cabinet has a 1-1/2" x 20" slot cross...

    My router cabinet has a 1-1/2" x 20" slot cross the top of the door that is open. Running the 2Hp Freud router for as little at ten minutes without the cabinet dust collector running the air in the...
  8. Replies
    3
    Views
    499

    There is quite a bit of activity and a lot of...

    There is quite a bit of activity and a lot of businesses near 297 Market St. in Philadelphia. You can google it and drop the little Yellow guy on the street and look around. Nothing woodworking...
  9. Very nice table. I really like the gain. I'm...

    Very nice table. I really like the gain. I'm curious as to how the table is supported. RV walls aren't generally structured to support a cantilevered table.
  10. Replies
    24
    Views
    1,333

    Very elegant work. I'm guessing it was outside...

    Very elegant work. I'm guessing it was outside to darken the cherry. What finish did you use?
  11. On my 10" blades, the thin kerf blade has a plate...

    On my 10" blades, the thin kerf blade has a plate thickness of 0.074 and a tooth width of 0.097 a difference of 0.023 or 0.0125 over hang from the plate on each side. My full kerf blade has a plate...
  12. The video shows that a properly glued joint (glue...

    The video shows that a properly glued joint (glue applied to both sides of the joint) is stronger than the lignin that holds the fibers together, but not nearly as strong as the fibers themselves. ...
  13. Replies
    14
    Views
    901

    I have a porch swing that has lived outdoors for...

    I have a porch swing that has lived outdoors for over 25 years and is still going strong. It is made from western red cedar with stainless steel hardware.

    We could give more precise advice if you...
  14. I use beeswax. I melt the wax and simply dip the...

    I use beeswax. I melt the wax and simply dip the end of the board into it.
  15. Replies
    14
    Views
    736

    Don't worry Ken, it happens to all of us. I...

    Don't worry Ken, it happens to all of us. I spent a hour yesterday looking for a partial spool of 1/8" braided nylon rope.

    You will now have two 16 oz hammers as the original one will...
  16. Replies
    61
    Views
    4,627

    I was at a wood show a number of years ago. ...

    I was at a wood show a number of years ago. There was a booth selling Hi-Pur glue that glued up samples of wood using their glue. The joints were all end grain to end grain. Shortly after gluing...
  17. You need a router bit like this: 464395 This...

    You need a router bit like this:
    464395

    This particular bit is a Craftsman 9-25567 with an 1/8" radius round over. You might find one here:...
  18. Replies
    27
    Views
    1,176

    Here's what you are up against. 464389 Unless...

    Here's what you are up against.
    464389

    Unless you use a spray with residual effectiveness or penetrate to the interior where the larvae are located, you will not kill them all.
  19. Replies
    24
    Views
    1,131

    I've used my Bosch multi tool for a variety of...

    I've used my Bosch multi tool for a variety of jobs.
    I've cut nails to removed boards during remodeling with the carbide tipped blades
    I shortened metal top hat duct work on my HVAC system in...
  20. I once removed an oil spot from concrete using a...

    I once removed an oil spot from concrete using a spray can of Gunk engine cleaner. That was 30+ years ago so the formulation may have changed.
  21. Try this link....

    Try this link. https://www.concordamericanflagpole.com/resources/design/foundation-options/

    I would find someone with a bucket truck or man lift to pick the pole up so it can be lowered over the...
  22. Replies
    13
    Views
    990

    You need a sewer line Fullport Backwater Valve,...

    You need a sewer line Fullport Backwater Valve, similar to this one.
  23. Replies
    1,534
    Views
    167,413

    Depending upon the year that coin could be worth...

    Depending upon the year that coin could be worth $225 -$1,000
  24. Replies
    1,534
    Views
    167,413

    Saw these while traveling

    These are actual signs:
    464025

    This sign was located in a State Park in California along a trail with a 150 foot drop. Note the location of the sign to the trail.
    464024

    I guess they want to...
  25. Replies
    17
    Views
    1,038

    Mix some black walnut sanding dust with pva glue...

    Mix some black walnut sanding dust with pva glue to make a wood putty. Fill the holes, sand it smooth and finish the project. Wood dust and pva glue are not considered toxic unless you possibly have...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4