I bought it to complete a christmas gift. It only took an hour before I got it to make noise. I downloaded lightburn and used the free trial to calibrate machine and setup a job. after that I changed...
Type: Posts; User: George Yetka; Keyword(s):
I bought it to complete a christmas gift. It only took an hour before I got it to make noise. I downloaded lightburn and used the free trial to calibrate machine and setup a job. after that I changed...
Is this a combination machine?
Definitely look at 6" there is a decent time savings with the 30% more surface area and paper is only about 10% more in cost.
If you have lots of 5" on hand I know at least the Mirka allows...
I bought the Grabo last summer and it allowed me to maneuver 50 pieces of sheet goods through my small shop with little back pain. The hardest part of the lifting of sheet goods is the awkwardness...
Spongy or "punky" wood is usually stabalized with epoxy. I know knife makers and pen makers do this if they work with spalted woods.
To stabilize you would want something very thin. The thicker stuff like the quick cures wont penetrate. This is total boats version
...
https://knottec.com/ these systems use a glue gun and an aluminum block to quickly cool the material. then flush trim it.
Smaller stuff you can use tinted CA if the colors will match I have used...
I would say you arent going too deep so a forstner bit freehand as long as holes are marked out properly and marked with an awl will work well. the more critical thing would be to make sure magnets...
Hers definitely warp. To the point they are uncuttable
Lock miter 2 sizes of ply strips you can make this 4' long or whatever you feel comfortable with working. Then glue and pin nail then chop to your length. The box will be plenty strong. Then screw...
Speaking as a northerner Id have to agree bbq generally means burgers, dogs, maybe kabobs, or grilled chicken. But being partially german we used to do a pig roast at any larger party in which the...
Wifes Hyundai sonota gets rotors and pads more than a f1 car. Every 20-30k sometimes under 20. The rotors are so poorly made that if you depress pedal more than say 75% the rotors will warp and eat...
I like the idea and there a few other companies that make them but for once the woodpecker product isnt too expensive. Ive been meaning to 3d print some
Ortur lasermaster 3 is $399 for 10 watt
https://ortur.net/
I have the mid size one. the advantages i see are the easy hookup to rails/edge guides and the dust collection is very good for a router
Id say im 60/40 60% love adding tools and improving shop. 40% enjoy projects
Blue skys all day, 230 rolled around and a giant cloud rolled right in front of the sun. Couldn't see a thing.
I keep waiting for the sun to pass between the Earth and the moon.
Check out the 3x3 custom base. $70 and is pretty multifunctional. I opened mine yesterday.
Agree with Jim on the 2nd combo blade. I would wait a while till your close to ready for sharpening and order that way the cost is spread out. An alternative is put factory combo back on while you...
I am a ridge guy. Mostly because he comes to the woodworking shows. I have about 6 of them and only 1 Forrest(dado set)
Id leave the supplied blade in the saw for a bit to get past any brake...
The pumps normally have significant filtration in them as far as the gunk goes. And reputable stations i would hope get the tanks pumped and cleaned occasionally to remove any buildup of water.
Everything above and it is also a material that gives the insulation a good amount of protection for the weight it adds. Also also the foil wont break down and fall apart. Commercially if it is a...
I love my electric cheapy. It does my vinyl siding/grill/cars/sidewalks(slowly)/Trex deck. Its light duty but 9/10 thats what im looking for. I borrow my mothers gas machine if I have to get...
General finishes Enduro recommends
Airless: 0.009”- 0.011” tip.