Search:

Type: Posts; User: Bruce Page; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.55 seconds.

  1. Darn clever!

    Darn clever!
  2. If proven effective, that will be a revolutionary...

    If proven effective, that will be a revolutionary treatment.
  3. Replies
    5
    Views
    218

    Great work Jim. I hope that's not your blood on...

    Great work Jim. I hope that's not your blood on the tissue!
  4. Replies
    9
    Views
    395

    Second that! Alan brings up a very good point...

    Second that!
    Alan brings up a very good point about maintenance. A thorough cleaning of my small (by comparison) 110gal is almost an all day affair.
  5. Very slick setup Bobby. It makes my Camaster...

    Very slick setup Bobby. It makes my Camaster "fast tool change" look Neander!
  6. Replies
    5
    Views
    453

    If it's just light surface rust, grey...

    If it's just light surface rust, grey Scotch-Brite and a little elbow grease will make it like new.
  7. Replies
    3
    Views
    329

    Slick setup. That's a long reach up to the...

    Slick setup. That's a long reach up to the ceiling.

    Welcome to the Creek!
  8. Replies
    5
    Views
    272

    That's awesome! Can't tell from the low res pics,...

    That's awesome! Can't tell from the low res pics, how did you assemble the wheels? That's a lot of spokes!
  9. Replies
    40
    Views
    1,270

    I did a few derby cars with my grandson. I let...

    I did a few derby cars with my grandson. I let him do the spindle sanding, etc, but not any cutting with the bandsaw. Disaster can occur before you can react.
  10. Replies
    5
    Views
    235

    Beautiful work Brad. The finish looks great!

    Beautiful work Brad. The finish looks great!
  11. Replies
    9
    Views
    396

    Very nice! What font is that?

    Very nice! What font is that?
  12. Replies
    41
    Views
    1,513

    Yowza! Simply stunning!

    Yowza!
    Simply stunning!
  13. Replies
    14
    Views
    773

    That is a beauty!

    That is a beauty!
  14. They're beautiful in walnut!

    They're beautiful in walnut!
  15. Replies
    8
    Views
    385

    Steampunk Santa Sleigh

    I finished this up yesterday just in time for Christmas. Done on my cnc router, it is from Michael Tyler’s & Vectric’s free project of the month program. It was a very well done model. I lost track...
  16. Replies
    12
    Views
    632

    I know the feeling!

    I know the feeling!
  17. Bob, you could try putting a 1/16" or 1/8" shim...

    Bob, you could try putting a 1/16" or 1/8" shim between where the foot lever and the wheel top plate intersect. I would start with 1/16", it should work.
  18. Replies
    12
    Views
    632

    Very nice looking table! Did you also do the...

    Very nice looking table! Did you also do the metal fabrication?
  19. Replies
    25
    Views
    1,162

    Robert, you do have to push the broach all the...

    Robert, you do have to push the broach all the way through. I raised the table as I went. Once you have the broach started into the work piece an inch or two it becomes self-aligned so positioning or...
  20. Replies
    5
    Views
    571

    It looks like you have more female friends than...

    It looks like you have more female friends than male! :)

    What material are they?
  21. Zach, just curious if you’ve looked at the...

    Zach, just curious if you’ve looked at the Camaster offerings. I’ve had a Stinger SR23 with spindle for over 6 years and have had zero problems or complaints with it, it just does what I tell it....
  22. Replies
    25
    Views
    1,162

    An unconventional method that makes beautifully...

    An unconventional method that makes beautifully square holes is broaching. You drill a pilot hole then using the DP as an arbor press, push the broach through. I picked up this broach and a couple of...
  23. Replies
    11
    Views
    726

    My first time seeing one, thanks for posting,...

    My first time seeing one, thanks for posting, Jim. I've always love that style & design.
    You know the main body had to be built like a tank.
  24. Replies
    9
    Views
    664

    First, never hit a chuck or spindle laterally,...

    First, never hit a chuck or spindle laterally, you can damage the machine’s spindle bearings and easily trash the chuck, (you may have shortened their life already). Check the spindle bore itself for...
  25. Replies
    11
    Views
    455

    Very cool. The only limit with cnc is your...

    Very cool. The only limit with cnc is your imagination!
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4