Search:

Type: Posts; User: Greg Funk; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    11
    Views
    1,683

    Because when a lithium battery is left on the...

    Because when a lithium battery is left on the shelf it can go into a severe undervoltage condition which the cells are not designed to handle. Leaving cells in a low-voltage state for an extended...
  2. Replies
    28
    Views
    3,482

    Usually the airline app will show the boarding...

    Usually the airline app will show the boarding pass with its bar code. All you need to do is take a screen shot of the pass and call that up when asked to show it. I've never stored a pass in google...
  3. Replies
    18
    Views
    2,520

    Keep the bits and chuck the rest. Looks like a...

    Keep the bits and chuck the rest. Looks like a quick jig or test piece for cutting some very specific dovetail cuts. Chances of you wanting to make something similar to the original owner are slim.
  4. Replies
    15
    Views
    2,127

    That's what I would do. At the end of the day it...

    That's what I would do. At the end of the day it makes no difference if the fence is at a slight angle like yours as long as it's square to the tables. Adjusting so you have an even gap between the...
  5. Replies
    15
    Views
    2,127

    Check that the 'caddy' or whatever it's called is...

    Check that the 'caddy' or whatever it's called is level with the tables. It's attached with a couple bolts to the base and there may be some play involved when tightening the bolts
    500674

    Also,...
  6. Replies
    15
    Views
    2,127

    I don't see any adjustments on mine. Take a...

    I don't see any adjustments on mine. Take a picture of the rear of the fence where it attaches to the adjustment mechanism. On mine the only way for the fence to be crooked like yours would be if the...
  7. Replies
    125
    Views
    15,240

    You must be used to bigger cheques than me :) We...

    You must be used to bigger cheques than me :) We can deposit up to $500k with mobile banking.
  8. Replies
    22
    Views
    1,802

    Sorry - I was looking at 'New Posts' and got lost...

    Sorry - I was looking at 'New Posts' and got lost :)
  9. Replies
    22
    Views
    1,802

    I would cut them to table length plus a little. I...

    I would cut them to table length plus a little. I don't see any advantage to milling longer boards. If your machines are setup properly the edges should be flat and square so no need to joint edges...
  10. Replies
    105
    Views
    9,345

    Where did you rent from? I rented a car in...

    Where did you rent from? I rented a car in Toronto recently at the airport (National) and they gave me a Polestar EV but didn't need it charged when I brought it back. Just curious what the normal...
  11. Replies
    105
    Views
    9,345

    I think they're administered by a charging...

    I think they're administered by a charging company for a monthly fee. Not as convenient or inexpensive as charging in a detached home but it's manageable.
  12. Replies
    105
    Views
    9,345

    To be fair most new condos in Vancouver are well...

    To be fair most new condos in Vancouver are well over $1000/sq ft so the incremental cost of adding a charger outlet is relatively low. There are a few pictures here of some typical installations:...
  13. Replies
    105
    Views
    9,345

    It doesn't have to happen overnight as even when...

    It doesn't have to happen overnight as even when a high percentage of new cars are EVs there will still be a large number of ICE vehicles for the next 20-30 years. Around Vancouver all new Multi-Unit...
  14. Replies
    105
    Views
    9,345

    The range certainly goes down in the winter but...

    The range certainly goes down in the winter but most EVs still have way more range than needed for daily commutes. I only use about 25-30% of the battery on a typical day so if the capacity was...
  15. Replies
    21
    Views
    3,105

    https://www.ctvnews.ca/politics/what-is-bill-c-18-...

    https://www.ctvnews.ca/politics/what-is-bill-c-18-and-how-do-i-know-if-google-is-blocking-my-news-content-1.6286816
  16. Replies
    21
    Views
    3,105

    I use NordVPN to spoof my IP and make it look...

    I use NordVPN to spoof my IP and make it look like I'm in the UK in order to watch bike races. Don't care about privacy. It is significantly slower than the fiber internet we have but works fine for...
  17. Replies
    39
    Views
    4,248

    In theory, if all the wires feeding the motor and...

    In theory, if all the wires feeding the motor and the internal motor windings had zero resistance you'd be correct. In reality, when a motor starts it can easily draw 6 time the FLA amps which, for a...
  18. Replies
    29
    Views
    2,889

    The breaker should be a maximum of 250% of the...

    The breaker should be a maximum of 250% of the FLA of the motor on the circuit (NEC table 430.52). In your case if the FLA is 12 the max breaker size is 30A so you should be OK.
    Change the plug on...
  19. Replies
    20
    Views
    1,884

    Depends how big a cut you're making. I like to...

    Depends how big a cut you're making. I like to put a lot of pressure on the board and climb cut. I've only used a 1hp feeder and would probably be uncomfortable cutting the power by a factor of 8. It...
  20. Yes they can sue you for negligence. Whether...

    Yes they can sue you for negligence. Whether they'd win is another question. You would be wise to carry liability insurance.
  21. Replies
    30
    Views
    3,852

    Looks like a medieval torture device :)

    Looks like a medieval torture device :)
  22. And this is the crux of the argument. What's...

    And this is the crux of the argument. What's reasonable for you might not be reasonable for an experienced woodworker. No different than any other activity. I'm not going to take a young child riding...
  23. Replies
    30
    Views
    3,852

    I made a bunch of moldings for our house with...

    I made a bunch of moldings for our house with this cutter. When it spins up you can feel it in your gut. I only ever used a power feeder but it's always a little unnerving when you make the first...
  24. Replies
    18
    Views
    2,532

    No problem sanding a tablesaw top. I've done it...

    No problem sanding a tablesaw top. I've done it when some moisture got on the top causing rust spots. I'd figure out what caused the scratches before doing too much on the top.
  25. Replies
    59
    Views
    8,642

    As you get older I think quality of life is...

    As you get older I think quality of life is important. For me that means staying fit in order to continue to do the things I enjoy. Cycling has been a great way for me to stay in shape and socialize....
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4