Search:

Type: Posts; User: woody dixon; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. 409864409865 The second picture shows the...

    409864409865

    The second picture shows the spring put back into the bottom of the guard with the shorter horizontal piece sticking in the slot and the longer verticall piece going down to the...
  2. Bill, If I try spinning the guard I get...

    Bill,

    If I try spinning the guard I get nothing. I suspect I have not loaded the spring properly into the shaft of the guard. There is an indentation under the top of the guard where i positioned...
  3. Replies
    10
    Views
    1,067

    i posted this in another thread and was...

    i posted this in another thread and was redirected here. I have a dj 20 with the same problem. I have taken it completely apart and the best I can do is get partial tension in the spring. People talk...
  4. I made the same mistake taking my guard off and...

    I made the same mistake taking my guard off and now the whole assembly came apart. I've read several threads, reviewed pictures, but I now get no tension when I reassemble. One thing I noticed is the...
  5. Replies
    24
    Views
    9,773

    Thanks Mike Woody

    Thanks Mike

    Woody
  6. Replies
    24
    Views
    9,773

    We can now round over the flutes. You have to be...

    We can now round over the flutes. You have to be careful in doing this because of the way the grain runs. On the top of each flute, I used the #2/8 and cut inward. But on the other side of the flute,...
  7. Replies
    20
    Views
    7,881

    Paul, Thanks for your offer. I've never done a...

    Paul,

    Thanks for your offer. I've never done a pm before and don't see that option. How do I access that option?

    Woody
  8. Replies
    20
    Views
    7,881

    Paul, Just read this thread with interest. I...

    Paul,

    Just read this thread with interest. I have been considering a clearvue but only have 84.5 inches to bottom of ceiling joists and 9 inches to bottom of floor above. Was trying to figure out...
  9. Replies
    81
    Views
    32,288

    Dave, I just came across this thread. Great...

    Dave,

    I just came across this thread. Great stuff. One thing I couldn't figure out on the first page was your method of marking the leg mortises. Could you explain how you "mark the centerline of...
  10. Replies
    4
    Views
    743

    I now have disassembled the gearbox to try to...

    I now have disassembled the gearbox to try to solve this. Grizzly tech support told me a bolt on the end of the shift lever was probably loose and not permitting the machine to shift into neutral or...
  11. Replies
    4
    Views
    743

    Okay think I figured out the problem. Had to take...

    Okay think I figured out the problem. Had to take more of the planer apart to have enough room to loosen the bolt attaching the swivel part to the body of the planer and swivel the part back under...
  12. Replies
    4
    Views
    743

    Grizzly 0453 planer outfeed rolller

    I have had this planer for several years. Today when planing a 3 inch piece of cherry the wood caught on the outfeed roller and jammed. When I tried to run it through again it stuck and I realized...
  13. Replies
    9
    Views
    1,112

    I think I already did that when I took everything...

    I think I already did that when I took everything apart before. I got this carriage level to both the infeed and outfeed table after I took the fence off. I don't see any other way to adjust for this...
  14. Replies
    9
    Views
    1,112

    Thanks Mike, I"ll let you know how the parts...

    Thanks Mike, I"ll let you know how the parts work. Still curious about the fence tilting up from the infeed to outfeed table. Is this normal? If not, how do I adjust this?
  15. Replies
    9
    Views
    1,112

    372128372129372132372133 Mike: Here are...

    372128372129372132372133
    Mike:

    Here are pictures of what I was talking about. 1 and 2 show the fence right after tightening and then moving at the bottom after using. 3 and 4 show the fence low...
  16. Replies
    9
    Views
    1,112

    Anybody have any ideas? Thanks.

    Anybody have any ideas? Thanks.
  17. Replies
    9
    Views
    1,112

    DJ 20 fence

    I have a 1986 delta invicta jointer made in Brazil. Everything works fine except the fence which won't stay at 90 degrees, After tightening and face planing a few boards, the bottom kicks back. I...
  18. Replies
    13
    Views
    1,519

    Thats what I am trying to visualize. The mortises...

    Thats what I am trying to visualize. The mortises are not curved but are at an angle with straight sides. Enclosed is a picture. The middle mortises could be cut with an edge guide riding against the...
  19. Replies
    13
    Views
    1,519

    If I make a template, is there an easy way to...

    If I make a template, is there an easy way to make it since the mortises are on a curve. Using a plunge router to cut the slots in the template I have no edge for a guide and freehand seems...
  20. Replies
    13
    Views
    1,519

    Chair rail mortise

    I am attempting to build my first chair and need help on how to cut mortises of the bottom of the top rail and top of the bottom rail. The rail is curved and therefore there is no straight edge for a...
  21. Replies
    5
    Views
    954

    I ended up ordering the grizzly handle even...

    I ended up ordering the grizzly handle even though they refused to give me the dimensions of the bolt. The exploded parts diagram for the grizzly 0490 and dj20 looked identical. The part came in...
  22. Replies
    5
    Views
    954

    dj 20 parts

    I am trying to replace the locking handle on my dj 20 jointer as it no longer locks completely down because some of the plastic threads underneath the handle are gone. All of the repair places online...
  23. Replies
    9
    Views
    1,630

    That's right Eric, it moves when I lock it down...

    That's right Eric, it moves when I lock it down not after. The only way to avoid this is to apply very small amounts of pressure on the cam and test for movement. I'll try your method when I get...
  24. Replies
    9
    Views
    1,630

    Biesemeyer Fence

    I have a Jet cabinet saw that I bought in the 90's with the original exacta fence. My patience is wearing thin with the movement of the fence when locking it down. The Biesemeyer 78-919B fence looks...
  25. Replies
    3
    Views
    849

    How do you rotate the infeed and outfeed rollers...

    How do you rotate the infeed and outfeed rollers then to get bdc?. My are locked up since the machine is in gear.


    Woody Dixon
Results 1 to 25 of 28
Page 1 of 2 1 2