Search:

Type: Posts; User: Michael Todrin; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    15
    Views
    975

    Keegan, I would use an RPC for the Maka. The...

    Keegan,

    I would use an RPC for the Maka. The Maka motor cycles on and off for each mortise and might be tricky doing that control from a VFD.

    Michael
  2. Replies
    15
    Views
    1,672

    Phillip, I ended up getting a Laguna Driftmaster...

    Phillip, I ended up getting a Laguna Driftmaster fence and have been quite happy with it.

    Michael

    459339
  3. Replies
    21
    Views
    1,156

    Nice fit Mark. The coolest top I have ever seen....

    Nice fit Mark. The coolest top I have ever seen.

    Michael
  4. Replies
    0
    Views
    439

    Maka STV Chisels

    Lot of 20 chisels for the Maka STV machine. In good to excellent condition. All chisels are sharp and many look unused. From 8-12 mm diameter and 10-55mm wide. Got them with some older tools and...
  5. Replies
    9
    Views
    2,181

    Love the proportions of that cherry door/entry...

    Love the proportions of that cherry door/entry way Mark.
  6. Replies
    8
    Views
    976

    Looks great Jim and with the compound splay I am...

    Looks great Jim and with the compound splay I am sure it is super stable. I think that will prove to be a very useful design. A fun trigonometry puzzle for sure. Well done.

    Michael
  7. Replies
    1
    Views
    361

    Used Machinery

    Has anyone purchased from Machinery Associates before? How were they to deal with?

    Thanks

    Michael
  8. Replies
    1
    Views
    574

    I was just browsing the cherry at Irion lumber in...

    I was just browsing the cherry at Irion lumber in PA and they probably have what you need. Sounds like a fun project.
  9. Thread: JNats

    by Michael Todrin
    Replies
    7
    Views
    835

    Ken, My hard finishing stone does not require...

    Ken,

    My hard finishing stone does not require anything more than a little water on top. I do have a softer stone that is a little less fine that I spray with water and wait a minute or two and...
  10. Thread: JNats

    by Michael Todrin
    Replies
    7
    Views
    835

    Ken, I am glad to share some thoughts on...

    Ken,

    I am glad to share some thoughts on Jnats. No real knowledge just some experimentation. For some reason rubbing the steel on the magic rock to make the wood shiny is one of the great...
  11. Replies
    16
    Views
    1,272

    Thanks for the wedge angle discussion gentlemen....

    Thanks for the wedge angle discussion gentlemen. For sure a shallower angle will allow tighter clamping and conforms more to what Will Myers has done.
  12. Replies
    16
    Views
    1,272

    I see what you are saying William. I did cut the...

    I see what you are saying William. I did cut the outside of the tusk mortise vertically and the wedge with one side vertical and the other matching the angle of the legs. What angle would you...
  13. Replies
    16
    Views
    1,272

    You would certainly win that bet Tom. Although I...

    You would certainly win that bet Tom. Although I found the hickory a little easier to plane than the white oak. Both required a very fine edge and frequent sharpening though.
  14. Replies
    16
    Views
    1,272

    Thanks Ken and Tony, I am excited to put it to...

    Thanks Ken and Tony, I am excited to put it to use. It was a big hickory, about 28" at chest high and still 20 inches 28 feet up. It came down in a storm.

    For vices I am will probably use the...
  15. Replies
    16
    Views
    1,272

    The Mighty Moravian Bench

    I have been meaning to build a Moravian bench to be used while doing site work and finally have had time to do it. Two slabs of 8/4 Hickory that I have been air drying for the last year and two 8...
  16. Replies
    21
    Views
    1,123

    Nice. Seems like a rock solid system for having...

    Nice. Seems like a rock solid system for having different fence positions.
  17. Replies
    21
    Views
    1,123

    Fine looking saw Darcy. What is that square hole...

    Fine looking saw Darcy. What is that square hole for in the bottom right corner of picture four?
  18. Replies
    12
    Views
    926

    Glad you are back at it James. The joy of the...

    Glad you are back at it James. The joy of the process is indeed the way.
  19. Thanks for sharing Mark. Great video, very...

    Thanks for sharing Mark. Great video, very informative. 100% worth hearing what he has to say.
  20. Replies
    6
    Views
    637

    Here is the tapping out hammer Jim. 429031

    Here is the tapping out hammer Jim.

    429031
  21. Replies
    6
    Views
    637

    Thanks Bill, it was actually quite an enjoyable...

    Thanks Bill, it was actually quite an enjoyable process.

    Jim, I am sure you could use a ball pein hammer for a striking surface. My thought process was that the larger diameter head would support...
  22. Replies
    6
    Views
    637

    Ura Dashi success, Cherry proof

    I have been working with Japanese planes for several years and they are now my go to planing tools. I am currently working on a cherry cabinet and it was time to smooth the panels after cutting all...
  23. Replies
    2
    Views
    1,947

    Let me know how it works for you Mike.

    Let me know how it works for you Mike.
  24. Replies
    19
    Views
    1,415

    First off, I agree with Jim that all these 24"...

    First off, I agree with Jim that all these 24" saws are serious business and that you should keep your smaller saw if possible. As far as which to choose there are a couple ways to look at this that...
  25. Replies
    2
    Views
    1,947

    Resaw guide

    Anyone who has the Jessem clear cut guides for their table saw has the opportunity to repurpose one of them as a resaw guide for the bandsaw. I took a 1.5 x 1.5 aluminum angle and some self tapping...
Results 1 to 25 of 137
Page 1 of 6 1 2 3 4