Search:

Type: Posts; User: glenn bradley; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.93 seconds.

  1. Will the motor turn freely by hand? The fact that...

    Will the motor turn freely by hand? The fact that you energize the motor directly bypassing the switch with no result does not bode well. Does the motor look as though it’s been stored outdoors or...
  2. Replies
    7
    Views
    382

    Elevate the Felder? I had to build a platform...

    Elevate the Felder? I had to build a platform for my Saw Stop. All my previous saws had been in the 36" height area and so all my fixtures were designed for that. When the shorty Saw Stop showed...
  3. Replies
    13
    Views
    426

    I also ran 3/4" dado stacks on my 1HP contractor...

    I also ran 3/4" dado stacks on my 1HP contractor without issue. No washer as discussed previously. The machine being up to the job may be the difference in viewpoint of the hobbyist / occasional...
  4. Replies
    7
    Views
    377

    This will be interesting. The home inspection...

    This will be interesting. The home inspection certainly should have shown this on the report. As an example, my clothes dryer electrical outlet was dead but, this was a non-issue as we use gas. ...
  5. Nope, plain old 1/8" pegboard for the most part. ...

    Nope, plain old 1/8" pegboard for the most part. I think it's only like $6 a year to join; I forgot about the picture viewing change.
  6. Replies
    11
    Views
    489

    It's fascinating that people still ask about...

    It's fascinating that people still ask about these things. I guess that's why they keep sending them.
  7. 500 here. Useful for many things. Not a...

    500 here. Useful for many things. Not a replacement for other joinery. Glad to have it.
  8. Things that work and don't work for me: Work -...

    Things that work and don't work for me:

    Work -

    Drawers, drawers, drawers; but not too deep
    Cabinet with doors; but not deeper than about 18"
    Pegboard; panels, end caps, inside doors
    ...
  9. Replies
    18
    Views
    870

    On the miter slots, I've never measured but, my...

    On the miter slots, I've never measured but, my various dual runner sleds all run well with no play so they are close enough for that. If the blade is at the upper end tier and has a half dozen or...
  10. Replies
    14
    Views
    787

    Definitely damaged, they are excellent about...

    Definitely damaged, they are excellent about Customer Service and replacements.
  11. Replies
    18
    Views
    1,130

    Agree. I ran a full kerf 24 tooth FTG even on my...

    Agree. I ran a full kerf 24 tooth FTG even on my 1HP contractor. Listen to your machine and adjust your feed rate so as not to overload it. Feather boards can help assure smooth cuts on longer...
  12. Replies
    54
    Views
    2,653

    The jointer in Maloof's shop. Canvas backed like...

    The jointer in Maloof's shop. Canvas backed like some tambours.

    417826

    Wish I would've gotten better pics of it. I keep meaning to drop by.
  13. Replies
    20
    Views
    1,045

    About 15 minutes into that process I would’ve...

    About 15 minutes into that process I would’ve used override mode. I am definitely curious to hear what Sawstop has to say though so please report back.
  14. Replies
    10
    Views
    490

    This may vary with the profile of your raise. If...

    This may vary with the profile of your raise. If there is a clean 1/4" 'tongue' with enough 'land' to fit I run a 1/4" wide x 3/8" deep groove and use space balls or silicone rubber to assure...
  15. Replies
    29
    Views
    1,407

    I’ve been running a Milwaukee 5625 for almost 15...

    I’ve been running a Milwaukee 5625 for almost 15 years. It never does anything but work. I run mine in a woodpecker PRL version one which is no longer available. There are many good lifts available...
  16. Replies
    8
    Views
    783

    Ding, ding, ding! Double-plus-good on the...

    Ding, ding, ding!

    Double-plus-good on the sleds and jigs. I have seen more folks post "why did I wait so long" regarding their first tablesaw sled than almost anything else.

    I also took awhile...
  17. Replies
    29
    Views
    1,407

    More food for thought. I also have my table on...

    More food for thought. I also have my table on the left; common feed direction and clearance requirements. I set my router table miter slot the same distance from the bit that the tablesaw miter...
  18. Replies
    18
    Views
    656

    If your push blocks are wearing out you may want...

    If your push blocks are wearing out you may want to look at your machine surface prep or your technique. You are probably fine but, just in case . . . You shouldn't have to push the material over...
  19. Replies
    35
    Views
    1,664

    I recently swapped the failing nylon/rubber (two...

    I recently swapped the failing nylon/rubber (two component) wheels on my Shop Fox for the cast iron replacement wheels. The originals lasted about 15 years. The replacements were reasonably priced...
  20. Replies
    8
    Views
    397

    I do as Jim does; BLO although I don’t flood the...

    I do as Jim does; BLO although I don’t flood the surface. I apply it with a rag. You can add a little bit of Japan dryer and it will cure more quickly, a day or two. The surface of one of my...
  21. Replies
    22
    Views
    7,989

    Freud SD 508 is my "go-to" although I have...

    Freud SD 508 is my "go-to" although I have others. The dial-a-width can be a godsend if you dado a lot.
  22. I will say that I prefer the 4" length (I have...

    I will say that I prefer the 4" length (I have the small Whiteside brass set) to the Lee Valley or Rockler ones that set in a drawer. Most machinist sets I have seen are also too small for my use in...
  23. Replies
    12
    Views
    1,247

    Thanks for sharing a beautiful box mike. Very...

    Thanks for sharing a beautiful box mike. Very inspirational.
  24. Replies
    5
    Views
    360

    I would glue several pieces between a couple of...

    I would glue several pieces between a couple of outriggers. Saw the out rigors off when you’re done.
  25. Replies
    11
    Views
    546

    Good info, thank you all. Lee, thanks for...

    Good info, thank you all. Lee, thanks for sharing that. It may be a concern.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4