Search:

Type: Posts; User: Roger Marty; Keyword(s):

Page 1 of 9 1 2 3 4

Search: Search took 0.02 seconds.

  1. Undermount drawer slides for 24" face frame cabinet

    I'm replacing drawers in my mother's run down kitchen. Cabinets are 24" deep with face frames. 22 7/8" from the back to the rear of the face.

    I did three with 22" side slides that are a bit...
  2. Replies
    9
    Views
    3,149

    Bosch has great customer service. My plunge base...

    Bosch has great customer service. My plunge base busted on me. No receipt, no proof of purchase. I called their customer service. I sent it to them and they turned around and sent me a new one. ...
  3. My Ipe stock is 5/4. I'd have to laminate and...

    My Ipe stock is 5/4. I'd have to laminate and was planning on West Systems Epoxy. Otherwise I also have 8/4 white oak on hand, but I don't think it would hold up to the outdoors like Ipe.
  4. Huh. Well my local wood wholesaler said this was...

    Huh. Well my local wood wholesaler said this was the best, most durable wood to use for my patio table. Wood's already purchased. Also my local high-end patio furniture store sells several Ipe...
  5. Table base design for a heavy patio table

    I've built a 76" x 37" patio table top out of Ipe wood. Super heavy stuff...the table top must weigh well north of 120 pounds!

    Now I need to make a base. I guess I'm leaning towards good ole'...
  6. Replies
    73
    Views
    12,603

    I started out cheap and built my first several...

    I started out cheap and built my first several pieces out of flat-sawn red oak. I regret it. My time and efforts are too valuable to use cheap wood. Now I choose cherry, mahagony, walnut, or exotics...
  7. Replies
    9
    Views
    4,964

    My cutting boards are often very slightly uneven...

    My cutting boards are often very slightly uneven :-(

    I don't think you want to send them through the planer. The end-grain can actually wreck your planer
  8. Replies
    10
    Views
    2,753

    I watched a video from Freud on making an...

    I watched a video from Freud on making an exterior door. They used Red Oak.
  9. Thanks. And by running too strong of a motor--...

    Thanks. And by running too strong of a motor-- in cases of stress a weaker motor would bind up rather than transferring increased force to these underprovisioned parts on the bandsaw?

    Honestly my...
  10. Upgrading motor on old Homecraft/Delta 10" bandsaw for occasional resawing

    I have one of those old cast-iron Homecraft/Delta 10" bandsaws. It is heavy and well-built. Has served me well in my small basement shop.

    I've even used it for light resawing work since it has a...
  11. Replies
    18
    Views
    3,056

    I recently made a white oak door. Awefully...

    I recently made a white oak door. Awefully heavy. If I were doing it again, I might choose Douglas Fir
  12. PureBond is pretty crappy. Lots of gaps. And my...

    PureBond is pretty crappy. Lots of gaps. And my last sheet of PureBond Maple had a wave of super thin maple which ultimately ruined my project since I sanded through it.

    The only decent plywood...
  13. Replies
    6
    Views
    1,178

    I used the fence rails to attach the auxiliary...

    I used the fence rails to attach the auxiliary table, and those don't extend to the left.
  14. Replies
    6
    Views
    1,178

    Yes, I recently did. I replaced the MDF SawStop...

    Yes, I recently did. I replaced the MDF SawStop extension table with my own creation. I'm generally pretty happy with it. I sandwiched a 3/4" plywood with a 1/2" plywood to get a bit more...
  15. Replies
    39
    Views
    7,842

    Congrats! You made a good choice.

    Congrats! You made a good choice.
  16. Replies
    39
    Views
    7,842

    Huge step up.

    Huge step up.
  17. Replies
    691
    Views
    98,823

    My DeWalt 734 benchtop planer had overload...

    My DeWalt 734 benchtop planer had overload problems. DeWalt replaced the switch and problem solver.

    I use a little 6" jointer I found on Craigslist for $75. Do I wish i had a big 8"? Yup. But...
  18. Replies
    19
    Views
    2,238

    I have and use a sled like that. I've used it...

    I have and use a sled like that. I've used it with rough sawn lumber. You should be fine. Careful where you stand. Definitely get a splitter though.
  19. Replies
    18
    Views
    2,979

    onedayglass.com will sell dual-paned insulated...

    onedayglass.com will sell dual-paned insulated tempered glass.

    I live in Wisconsin. -50 degrees to 100 degrees F ;-)

    Right now I'm simply trying to decide whether to order 5/8" or 1/2"...
  20. Replies
    18
    Views
    2,979

    One side is open. I'll make marching trim to...

    One side is open. I'll make marching trim to hold in the glass.
  21. Replies
    18
    Views
    2,979

    Question for ordering door glass

    Newbie making an exterior door (and so many experts on this forum!).

    I need to order some double-paned glass. The Freud cope-and-stick router bits create a slot of 5/8" (of course I routed...
  22. I'm 41. I've been driving for 25 years and have...

    I'm 41. I've been driving for 25 years and have pretty much never made a mistake.

    Today I was spaced out driving the car and blew through a red light (I slammed the brakes but not nearly in...
  23. FWIW, the door faces West / NorthWest. Sounds...

    FWIW, the door faces West / NorthWest.

    Sounds like I should drawbore it with glue.

    Looks like I can find Rescorcinol: ...
  24. Most of this door will be glass which should...

    Most of this door will be glass which should help...
  25. What would you use for glue?

    What would you use for glue?
Results 1 to 25 of 204
Page 1 of 9 1 2 3 4