Search:

Type: Posts; User: Matt Day; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.77 seconds.

  1. Replies
    24
    Views
    1,241

    No ZCI is truly Zero clearance. The teeth are...

    No ZCI is truly Zero clearance. The teeth are wider than the plate of the blade so there will be a very small gap. But, Iím not sure how a 1/4Ē cutoff would cause a problem. I trim stuff like that...
  2. Replies
    41
    Views
    3,567

    I would not buy an opened ended drum sander...

    I would not buy an opened ended drum sander again. Too much flex leading to variance.
  3. Make some test holes in the same wood. I usually...

    Make some test holes in the same wood. I usually use a punch to located the hole so the bit doesnít wander.
  4. Replies
    29
    Views
    1,349

    I mustíve turned those features off because I...

    I mustíve turned those features off because I havenít been asked for a review in years.

    As far as their price is changing, they have all kinds of algorithms that change prices based on all kinds...
  5. Replies
    10
    Views
    718

    My go to for all things clean up of dirty grungy...

    My go to for all things clean up of dirty grungy metal is my pedastal grinder with scotch brite wheel. If itís really bad it hits the wire wheel first.
  6. Replies
    10
    Views
    954

    I just felt the euphoria with my brand new...

    I just felt the euphoria with my brand new Festool track saw cutting melamine without a chip out to be seen.
  7. FS: Shark Guard throat plates for Unisaw and Jet JTAS

    I have Shark Guard throat plates for Delta Unisaw left tilt (8) and Jet JTAS ďsmallĒ (2). These are great quality plates. Note that they will not work with the ARK without modification, but will work...
  8. Bump to the top!

    Bump to the top!
  9. Jim, I think Iím going to make that side of the...

    Jim, I think Iím going to make that side of the cabinet a little long and scribe the actually cabinet box, instead of scribing trim. Iíll probably make scribe a template then transfer to the cabinet.
  10. I was going to say that would be a lot of...

    I was going to say that would be a lot of scribing, but you were saying just on that one exposed edge piece. That makes sense, I like it. Thanks for the tip!
  11. Mudroom locker install - Out of plumb wall?

    Iím renovating our mudroom and installing cabinets and lockers. The first section of the install is the main piece, a floor to ceiling set of lockers. The bottom 2í or so will be a bench with shoe...
  12. Replies
    6
    Views
    1,475

    He hasnít logged on since the 4th when he last...

    He hasnít logged on since the 4th when he last posted.
  13. Sanding pads and planer blade sharpener spoken...

    Sanding pads and planer blade sharpener spoken for.
  14. FS: Misc clean out the shop items - all $15and under!

    Porter cable sander pads $10
    Kreg hinge jig - $15
    Planer blade sharpener - $5
    Dewalt sanding pads $5
    Diablo well used dado set (1 complete + extras) - $10
    Craftsman (vintage) throat plates and...
  15. Replies
    12
    Views
    726

    Having a single long track and a short track not...

    Having a single long track and a short track not only speeds up your work but itís a lot less frustrating and fussy.

    I would caution you to try to have the same tracks for both. Reason being is...
  16. Replies
    29
    Views
    1,849

    Big box stores have birch plywood, NOT Baltic...

    Big box stores have birch plywood, NOT Baltic birch. At least for HD, Loweís, and Menards. Big box store plywood has a bad habit of turning into a potato chip.
  17. Replies
    1
    Views
    516

    I had the opposite experience last week - got a...

    I had the opposite experience last week - got a bum TS55 from Recon where the locking mechanism had been jammed very hard and twisted the base plate. Likely dropped on the handle or something. Had...
  18. Replies
    16
    Views
    1,047

    You guys must have a lot of stuff to hide if...

    You guys must have a lot of stuff to hide if youíre worried about anyone (or anything) hearing it!
  19. My saws are right tilt, and cut on the left side...

    My saws are right tilt, and cut on the left side of the fence.
  20. Replies
    17
    Views
    1,201

    The planer (one n, unless youíre planning to do...

    The planer (one n, unless youíre planning to do something) doesnít flatten anything, it makes one side parallel to another. You need to face joint it, on a jointer, first then plane. Youíll be taking...
  21. Thread: Kumiko

    by Matt Day
    Replies
    19
    Views
    1,968

    Matt R, Just a heads up but to post pictures you...

    Matt R,
    Just a heads up but to post pictures you need to be a contributor. A measly $6/yr.
  22. Replies
    17
    Views
    1,128

    Myk, just a heads up but Lynn retired about a...

    Myk, just a heads up but Lynn retired about a year ago. I believe Jennifer took over the OWWM group.
  23. Replies
    17
    Views
    1,128

    Accurate Bearing is my go to for most bearings...

    Accurate Bearing is my go to for most bearings especially odd and hard to source bearings. Otherwise amazon, Fastenal, eBay.
  24. Replies
    51
    Views
    4,691

    I just heard an article on the news that Ford is...

    I just heard an article on the news that Ford is building a new plant just for the Ford lightning. Will cost something like $20 billion or something, and the first new plant in 30 years. So theyíre...
  25. Thatís a meat saw. Duro possibly.

    Thatís a meat saw. Duro possibly.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4