Search:

Type: Posts; User: Bill Gebhardt; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    13
    Views
    2,510

    It has been a month now and I have eaten enough...

    It has been a month now and I have eaten enough crow to confess my ineptness and apologize to PSI.

    PSI did well. I wrote to them explaining in detail the issue and gave them different ways to...
  2. Replies
    13
    Views
    2,510

    I gave it rest until yesterday when I started...

    I gave it rest until yesterday when I started playing around with the Receiver. I took it off the board it was nailed uupon and discovered the programing button. It is below the surface, almost...
  3. Replies
    13
    Views
    2,510

    Well, I finally talked with Ken at PSI on...

    Well, I finally talked with Ken at PSI on 800-377-7297, who shared some more silly, in the translation from Chinese to English, the words (three times) were dropped.
    From the instructions, "Press...
  4. Replies
    13
    Views
    2,510

    On the battery issue: Programing the...

    On the battery issue: Programing the remote/transmitter, (that has batteries and the LED lights up), the 1st step is to start with the receiver, (only power 220vac, no batt) by pressing a button,...
  5. Replies
    13
    Views
    2,510

    Bill, the problem is I purchased a second remote...

    Bill, the problem is I purchased a second remote (bought a second saw) for the Long Ranger that was served me well for over 10 years. The second remote worked well until about a week ago. The first...
  6. Replies
    13
    Views
    2,510

    connecting with PSI Woodworking

    I need help from PSI on their Long Ranger transmiters. When I send a message to psind@pennstateind.com it comes back Blocked.

    Because I am hearing impaired and dependent on email/text/etc I can...
  7. Replies
    7
    Views
    2,304

    camera for dust collector ducts

    Has anyone tried to use a pipe inspection camera to locate a clog duct to their dust collector?
    Bill
  8. Thanks all, went with a 35" x 5' aluminum ramp...

    Thanks all, went with a 35" x 5' aluminum ramp from Allegro Medical Sales.
    Bill
  9. Replies
    7
    Views
    1,127

    Gentlemen, thank you for your interest and ideas....

    Gentlemen, thank you for your interest and ideas. Wish I had thought of a rectangle and cut the corners before all this consternation. Buxton’s popsicle sticks got me started. Then I spotted some of...
  10. Replies
    7
    Views
    1,127

    clamping a single box joint

    So how does one glue up a single box joint? A friend has asked me to memorialize
    a pair of bricks salvaged from her high school that burned down back in the Forties.
    Her vision was a pair of...
  11. Threshold for new concrete on existing concrete

    I need to build a ramp to over come a 5" step into the shop. This will enable me to ride my mobility scooter in to the shop. The issue is how to deal with the concrete when it tapers off to 0 at the...
  12. New twist/turn on age old self-centering jig

    We are all familiar with self-centering jigs for routers that have two pins inline with the bit but spaced apart enough to keep the bit on center when the router is twisted. I have 6 dados 30" long...
  13. Replies
    1
    Views
    1,262

    Prepping Redwood

    A Korbel Redwood we planted 21 years ago finally succumbed to bifurcation, (trunk split 20’ above the ground) and will be taken down next month. It has a diameter of 17”. What I have read on other...
  14. Replies
    11
    Views
    1,873

    Cutting boards

    Asked to make a thick cutting board with 13/16 wood my thought was to just rip the stock little over the desired thickness and glue up the faces. Then I heard the that the edges were a poor surface...
  15. Replies
    5
    Views
    826

    Cary, Thanks for the correction, it feels like...

    Cary, Thanks for the correction, it feels like 11K. Good research, but I'm a little leery at such a low figure and free shipping on a 60# motor .
    Bill
  16. Replies
    5
    Views
    826

    PM 2000, chapter 2

    This is a new twist on my earlier "PM 2000 inop" I found a repair shop seemingly well qualified. Durham Pump & Well serves the bulk of all the irrigation needs of rice and orchards in our area. They...
  17. Replies
    8
    Views
    990

    Correction, it is a 3hp, not 5. Bill

    Correction, it is a 3hp, not 5.
    Bill
  18. Replies
    8
    Views
    990

    PWRMATIC 2000 Mtr inop

    Forgot and left My Powermatic 2000 run for an hour unattended. Motor too hot to touch. Next day it started running backwards, replaced starter capacitor, zip. Anyone pulled that 5hp, 1ph, 240v...
  19. Replies
    10
    Views
    1,511

    Thanks to all for your interest in my new...

    Thanks to all for your interest in my new venture. It all started when a limb from a Chinese Pistache came down and I thought about making bowls. Little did I know about wood splitting and pith. But...
  20. Replies
    10
    Views
    1,511

    Yet another newbie

    Very new to turning I Recently acquired a used Delta 46-460. While waiting for parts, (hardware mounting the motor) I replaced both switches. Discovered there is no faceplate and not sure when I will...
  21. Replies
    16
    Views
    2,260

    Thanks for all the good ideas, some of which have...

    Thanks for all the good ideas, some of which have me concentrating on:

    this: but not with IKEA.


    Bill Gebhardt
  22. Replies
    16
    Views
    2,260

    secret compartment

    Granddaughter asked me to make a bedside table with a secret compartment. Has anyone tried this?
    Here is a pic I made in SketchUp. It looks a little heavy because of the top rail on the end that is...
  23. Replies
    1
    Views
    573

    DeWalt 735 cutter head

    Has anybody changed out the cutter head on a DeWalt 735?
  24. Replies
    7
    Views
    1,051

    Thank you for Carl Holmgren reference. His system...

    Thank you for Carl Holmgren reference. His system for the Mechanic's cabinet is just what I'm looking for.
    Bill
  25. Replies
    7
    Views
    1,051

    retractable wheels

    Looking for retractable wheels/casters that I can hide inside the base of a podium. Once a week this podium is moved from closet to meeting room and back. The other option is a skirt around the base...
Results 1 to 25 of 38
Page 1 of 2 1 2