Search:

Type: Posts; User: Kevin Jenness; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. When I worked in a shop that had both a track saw...

    When I worked in a shop that had both a track saw and a full size sliding table saw I would have received the side eye at best and more likely a good razzing if I had suggested using the track saw...
  2. Replies
    2
    Views
    80

    Single phase motors have capacitors and...

    Single phase motors have capacitors and centrifugal switches to get started, so more complex and potentially prone to failure. Other benefits to three phase equipment are smaller conductors and a...
  3. Replies
    16
    Views
    736

    With a 49" rip capacity that saw will be close to...

    With a 49" rip capacity that saw will be close to 5' to the right of the blade and likely will take up about 6' from the blade to the end of the crosscut fence. if the parts are next door you should...
  4. Replies
    10
    Views
    1,390

    Did you get in touch with Camaster tech support...

    Did you get in touch with Camaster tech support initially? I have had a call back within a day when I have needed help.
  5. For me the advantage of a slider is as much about...

    For me the advantage of a slider is as much about ergonomics and saving my back as about saving time. You appear relatively young - if you stick with it by the time you are my age you will have...
  6. Replies
    16
    Views
    736

    A neighbor has a similar Robland saw (8') and is...

    A neighbor has a similar Robland saw (8') and is happy with it. I haven't used it but it looks to be on a par with my Paoloni and the MiniMax line for overall build quality. I would say it is a...
  7. Yes. The cyclone will add resistance to the...

    Yes. The cyclone will add resistance to the system but the cartridge filter will offer less resistance when clean.
  8. The 1100 cfm figure is at 0" static pressure with...

    The 1100 cfm figure is at 0" static pressure with the stock filter in place and 5' of inlet hose. Flow figures are meaningless without an associated static pressure. The new filter will help with...
  9. Same power, different run times. I have 2 A/hr...

    Same power, different run times. I have 2 A/hr batteries on my Bosch 18v drill/driver set and they work fine. A 5A/hr battery would be nice for work out of the shop, but with a charger at hand I...
  10. The gray wheels are practically worthless for...

    The gray wheels are practically worthless for grinding tools efficiently. The difference between them and the white wheels is less than that between white wheels and cbn. A 6 white wheel is about $25...
  11. Replies
    7
    Views
    964

    I made a close replica of Hannes Michelson's...

    I made a close replica of Hannes Michelson's Vector jig using a wood platform screwed to the Wolverine arm and played with the pivot locations and Varigrind settings. I was able to get very close to...
  12. You can take the temper out of carbon steel with...

    You can take the temper out of carbon steel with any type of grinder if you are not paying attention. CBN makes it more difficult. I think CBN wheels are a good investment if you use a grinder much...
  13. I use 180 and 600 grit cbn wheels on a slow speed...

    I use 180 and 600 grit cbn wheels on a slow speed (1040 rpm) 6" grinder for all my edge tools. I bought them initially for hss turning tools but have not seen a problem with carbon tool steels for...
  14. Replies
    6
    Views
    1,040

    Thanks, but I am looking for a large swing lathe...

    Thanks, but I am looking for a large swing lathe within drivlng distance from VT. If that was an American Beauty for $3500 I would make the trip!
  15. If you are getting significant amounts of dust in...

    If you are getting significant amounts of dust in the closet there is some leakage in the system.
  16. Replies
    6
    Views
    1,040

    I am going to pass on this but here is the...

    I am going to pass on this but here is the listing for anyone who might be interested....
  17. Replies
    13
    Views
    628

    Whether you need a braking resistor depends on...

    Whether you need a braking resistor depends on how much inertia the cutterhead has and how fast you want it to decelerate. If the vfd shuts down at the default deceleration rate you can either...
  18. Use a water level.

    Use a water level.
  19. Replies
    8
    Views
    1,001

    So what is the point of doing it that way?

    So what is the point of doing it that way?
  20. Replies
    8
    Views
    1,001

    I'm not sure what you would gain by using a...

    I'm not sure what you would gain by using a faceplate on the tailstock end over a live center in a recess. You would have to face off that end to start with and get the faceplate accurately mounted...
  21. Replies
    26
    Views
    1,617

    If you feel the fence is sturdy enough to mount...

    If you feel the fence is sturdy enough to mount the clamps to then use heavier gauge material for the bracket. That fence extrusion looks a bit light for the purpose but you are in a better position...
  22. Replies
    1
    Views
    539

    Sent you a pm.

    Sent you a pm.
  23. Replies
    26
    Views
    1,617

    The clamps need to be mounted independent of the...

    The clamps need to be mounted independent of the fence. The central post of the miter gauge might be stout enough, or you can use other tapped holes in the table to mount brackets. Cam clamps I have...
  24. Replies
    6
    Views
    1,040

    The offer is for local pickup only. I could hire...

    The offer is for local pickup only. I could hire a rigger and have requested a quote from one down there, but that can be pricy. It's hard to judge whom to hire at a distance, so I am hoping someone...
  25. My son, a timber framer, has a French friend who...

    My son, a timber framer, has a French friend who works with his father in timber frame restoration and is bidding in concert with another company on some aspect of the roof system. It's a long shot,...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4