Ok tried simple solution tonight but not completely successful. Probably dont have Tom's feel because when I raise the knive to just touch it goes too high so the knife moves. "Then I have the same...
Type: Posts; User: woody dixon; Keyword(s):
Ok tried simple solution tonight but not completely successful. Probably dont have Tom's feel because when I raise the knive to just touch it goes too high so the knife moves. "Then I have the same...
Complete failure today. Never could get the cutterhead locked for long. Fooled around with the motor pulley/belt but could not see how to clamp it so it wouldnt move at all. Tried wedges with 4 oem...
I think this may work. I went down a put a vise grip on the pulley belt and clipped it inside the frame which locks the cutterhead. Is this what you had in mind? Your sequence is sort of what i was...
475866
I am trying to change straight knives on a dj20 jointer with a dial indicator. There was an old thread here that Rick Lizek posted to where he suggested using the jack screws to raise the...
468148468149468150468151468152468153468154468155
Here are photos of my setup. I cant get one showing the whole thing at once because of low ceiling obstructed by columns and radiator pipes as I...
I dont disagree with what you say. I havWe heard the same things. I am certainly no expert in this area . I am only reporting what I did, how the performance improved dramatically when run afterward...
Yes. I explained everything to Paul Bushey, showed him where the gaps were where the filters were mounted, how I remounted them eliminating the gaps and he said that could have been the cause of the...
Yes there was a problem. I have been talking, emailing, texting and exchanging videos and pics with Paul Bushey. We went over everything Monday including the changes I made to the filter mountings...
David,
I have disconnected 2 drops and 1 now has no gate. I tried hanging a 10 lb dumbell off a cup hook screwed into 3/4 inch plywood covering a wye drop and the booard wanted to slide off at a...
Ok. Just ran another test along the lines of John's suggestion. I disconnected the drop to jointer, a 6 inch wye, so it was not completely vertical. I took a pack of printer paper(500 sheets) which...
Here is a video of a test I made earlier this morning. The box is 2.5 lb and was sucked up tight to the bottom of 6 inch flex disconnected from my jointer. Would this now be the correct air flow and...
I dont know but how do I know if I have a 16 inch housing? The impeller is definitely rotating counterclockwise. I did have a strange thing happen the last time I checked this when powering down....
Chris,
One problem with the whole process is I dont know what proper airflow and suction feel like for the clearvue . My experience is with a harbor freight and the intitial flow and suction at my...
Stan,
I had this concern earlier and talked with clearvue about this. I had to put the motor between my ceiling joists myself. To do so I put the motor up without the impeller which I attached...
Getting there. Just rehung the filters after redoing gamma seals and extensive caulking and flow much improved. Concentrating now on 6 inch blast gate that still has whistling air when closed. Others...
I ont think so but how do I check without disassembly? Ive had the exhaust outlet disconnected several times and air flow out was strong but weak suction at drops. Dont know how I could get blockage...
Already done this. Felt alot more air at the exhaust but not that much more air flow or suction at equipment drops. My concern with the plenum is with the gamma seal connections. It seems the weight...
I was just doing what i have been advised to by Clearvue and others. My problem was either incorrect impeller rotation or leaks in the system. Impeller is correct. What do you think the right tool...
One more difference in my setup. I built a filter plenum and used gamma seal filters to hand my filters side by side under the box. I did this because my filters did not come with a ring on top or...
I have been in contact with support at Clearvue and Paul Bushey himself, and everyone has been pleasant and tried to help, but so far no success. I am asking Paul to pass my email on to people in my...
Have now smoke tested the top of the blower housing where it meets the motor plate and can see smoke moving from right to left towards the exhaust. I dont see any movement or air being sucked in at...
I have a 5 hp but a 15 inch impeller. The amps I tested were running not startup amps. I dont have to read about the performance of the clearvue, I already have, and thats precisely why i am...
https://youtu.be/8AIITfs51PE
Here is a video showing what I was trying to copy for my miter saw. My saw is a dewalt 708 with the port a little left and lower but I aligned it with the 6 inch port...
Trying to get my new clearvue up and running properly with great difficulty. My old dust collector was a modified harbor freight and to me the air flow on this new one is substantially more than...
Bob and Larry were kind enough to reply but unfortunately they did not remember the connections they made. This was a pretty big thread and many people posted and built the bin sensor so I cant...