Matt,
I am the guy that made that video and that blade is a 12" (300mm) blade. Toe-out is necessary on the sliding table trajectory since we can seldom adjust things to where they are perfect and...
Type: Posts; User: Steve Rowe; Keyword(s):
Matt,
I am the guy that made that video and that blade is a 12" (300mm) blade. Toe-out is necessary on the sliding table trajectory since we can seldom adjust things to where they are perfect and...
That's good to hear.
I am glad that solved your issue. I do find it disturbing that you have line power to your machine when the RPC is off. You really need to run from a single power source through a single disconnect...
Roger, I have the same machine but with a 5.5 HP motor and is a 2007 model. I had a similar problem in the first year of ownership but it would only happen intermittently after the machine had been...
Thanks Joe, That is an interesting attachment to the stop. I doubt that it would work on the two point contact fence though.
I'll see you in about 3 weeks - looking forward to absorbing some...
John took the jig up several notches and I had to turn over the Extreme Woodworker man-card. We had a great visit several weeks ago and what seemed like only a few minutes was actually over a 2 hour...
Awesome report John. Congratulations
Steve
Glad you are OK and that is going to leave a scar. This is clear evidence that one should never cut a piece that small on the tablesaw without it being adequately secured to a jig or fixture. ...
When attaching a vacuum to a sander, I find the variable suction a near necessity. I always move the suction to the middle setting for ease of control during sanding. Too much suction and the pad...
Check with riggers local to the machine. Sometimes they offer a service to pickup, crate, and put on a truck. There is one rigger in my area that does this and the service has been used by a...
We don't get American Woodshop in our area so cannot comment on your observation. While I always like to watch Woodright Shop, my all time favorite was Woodworks with David Marks followed by Norm...
I would check out Magnate but the longest cutting length they offer is 2". This is the link to the pattern bit but they also have flush trimming bits of the same length. One suggestion would be to...
Amerex 5 lb dry chemical mounted by door right under first aid kit. This brand has metal handle and mounting bracket unlike some other brands that have plastic handles and mounting brackets/straps. ...
The only one I would consider in that price range is the Hammer K3.
John,
I don't have a Jet J/P but do have experience with both Felder and MM J/P. You really haven't been specific on what is out but based on the info you have provided, I would surmize it is a...
Pizzi makes a glue applicator for the Domino but it is for a glue gun. Rangate has them. http://www.rangate.com/specialtyproducts/pizzi_glue_applicator_spreader.php
I wonder if the OP would be equally ticked off for a $500 griz that needed a $130 motor? After all, a cheaper HF with a coupon is much less and just as good. Just food for thought.
I had one and used in the shop until about 3 years ago. Bottom line, if you live in a humid environment, don't bother.
I will ditto what Van has said. I have a 10 year old LT18 made by ACM which has been a fine saw. I had upgraded the LT18 with ceramic guides right after they were introduced since I never really...
I purchased a Mikiway MB250 saw in 1985 from Bratton Machinery in Tallahasee. It is the 10"/3HP version of what is listed. I recall the price new was $999. A sliding table attachment was available...
With that width, a minimum of 5 hp, perhaps 7.5 hp.
George - about 7 years ago I went from separate Bridgewood 8" jointer and 13" planer (both fine machines BTW) to a Felder CF741 full combo with the 16" J/P. I have since gone back to separates for...
I am not so sure that is true universally. I have a Laguna LT-18 and the door will not open without tilting the table to at least 30 degrees with the Driftmaster. It has nothing to do with the...
Try continuing to loosen the collet nut. Later models have a self release collet.
I used the Lamello hinges for a project just several months ago. The mortise is cut with a biscuit joiner. I used a Lamello on the D setting which is for the Duplex hinges. This setting is deeper...