Search:

Type: Posts; User: Lance Mirrer; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    984

    The Hamlet pictured is a Spindle Roughing Gouge....

    The Hamlet pictured is a Spindle Roughing Gouge. Not a Bowl gouge.
  2. Replies
    14
    Views
    976

    Love your bench Derek. And thanks to all who...

    Love your bench Derek. And thanks to all who answered!

    I was concerned as I start making holes that i'd be turning the top into swiss cheese.

    Which begs the follow up question of what pattern...
  3. Replies
    14
    Views
    976

    Doug, I'm not sure permanently closing the...

    Doug,
    I'm not sure permanently closing the square holes is valuable. Possible a temp plug, so square or round can be used.
  4. Replies
    14
    Views
    976

    Matt, What would the sleeve do that is not...

    Matt,
    What would the sleeve do that is not accomplished by just drilling a 3/4" hole? I'm assuming the answer is 2 sets of holes, one round one square. The pic's below appear nice.
  5. Replies
    14
    Views
    976

    Workbench - square holes to round

    I have an old workbench with square bench dog holes.

    I also have many round accessories; benchdogs, holdfasts, etc.

    Is there a better solution to using my round accessories than drilling an...
  6. Replies
    3
    Views
    567

    Who is the author? Found it thanks!

    Who is the author?
    Found it thanks!
  7. Kyle, Thanks for your comment. I agree...

    Kyle,

    Thanks for your comment.

    I agree with your surprise of both jaws not seating correctly. They are installed in correct order and jaws are being installed to correct positions.
    ...
  8. Nova Infinity Chuck; Who owns, need tech discussion

    Hi,

    Just started working with NOVA's infinity chucks. This is the chuck with the "easy to change" jaws. The first thing I noticed was two of the jaws appeared to not seat correctly. Spoke to Nova...
  9. Replies
    0
    Views
    365

    Nova Chuck Jaws

    Woodturning chuck jaws. 25, 50, & 100mm. $50 per set.

    Have 2 @25mm
    4@50mm
    1@100mm

    I use them on a Nova Supernova Chuck. They are interchangeable and fit on all Nova Chucks.

    Thanks for...
  10. Clean your mailbox. Sent a note and got error...

    Clean your mailbox. Sent a note and got error message you were full
  11. sent PM. I have an extra Proxxon

    sent PM. I have an extra Proxxon
  12. Hi John, Sent you a PM about tools for...

    Hi John,

    Sent you a PM about tools for students

    Lance
  13. Sent PM for 3 tool rests, sizing and bedan tool.

    Sent PM for 3 tool rests, sizing and bedan tool.
  14. Replies
    3
    Views
    908

    sending PM

    sending PM
  15. sending PM

    sending PM
  16. Sent PM. Thanks

    Sent PM. Thanks
  17. Replies
    2
    Views
    790

    Sending PM

    Sending PM
  18. Replies
    11
    Views
    1,400

    Thanks for the responses and advice. Will start...

    Thanks for the responses and advice. Will start disassembling and cleaning.
  19. Replies
    11
    Views
    1,400

    Oil in Air Nailers

    Hi All,

    I have several air nailers that have not been used in years. picked one, worked for a handful of nails than died. I'm thinking that before using these, I should oil the seal s and...
  20. Replies
    6
    Views
    860

    How Upgraded was your HF? I am on the fence...

    How Upgraded was your HF? I am on the fence whether to add the larger impeller or go for new cyclone.
  21. Replies
    16
    Views
    3,725

    Excellent suggestion Robert. I was looking for...

    Excellent suggestion Robert. I was looking for something similar to place under my Tablesaw extension and couldn't find an appropriate height. I need the mobility (the lathe has wheels) so I can...
  22. Replies
    16
    Views
    3,725

    Hilarious!!!! Of course, you don't know how big...

    Hilarious!!!! Of course, you don't know how big my bed is...
  23. Replies
    16
    Views
    3,725

    Very Nice! I have found many pics. I'm hoping...

    Very Nice! I have found many pics. I'm hoping someone has plans or a Sketchup file so I can customize.
  24. Replies
    16
    Views
    3,725

    Love it John!! To help with things that fall...

    Love it John!! To help with things that fall through the ways, I have a 1/8" piece of 4" wide board running length of lathe bed under the ways.
  25. The harbor freight is very decent for it's size...

    The harbor freight is very decent for it's size and price. I have been using mine for several years. Note, it needed "help" out of the box. things like tightening screws by all seals, adding support...
Results 1 to 25 of 46
Page 1 of 2 1 2