Search:

Type: Posts; User: Lee Schierer; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.76 seconds.

  1. Replies
    11
    Views
    304

    I have used quite a few of the K&V 8419 slides...

    I have used quite a few of the K&V 8419 slides and I like them. The soft close is nice.
  2. Replies
    3
    Views
    198

    The plans here:...

    The plans here: https://www.pinterest.com/pin/347692033716588356/
    Are supposedly free

    There are some really nice plans in "The Great All American Wooden Toy Book" by Norm Marshall.
  3. Replies
    13
    Views
    445

    Check any local used equipment dealers as there...

    Check any local used equipment dealers as there may be serviceable used equipment that would do the job for you at a reduced price.
  4. Replies
    11
    Views
    304

    For maximum access to your "treasure" I would go...

    For maximum access to your "treasure" I would go with 16" slides. With over travel slides the longer slide will get the back of the drawer to open further and give you the best access to your...
  5. Replies
    11
    Views
    480

    Very nice table. I like the tiger maple and the...

    Very nice table. I like the tiger maple and the natural finish. Good job.
  6. Knowing which saw you have would help. On my...

    Knowing which saw you have would help.

    On my Craftsman saw, I struggled to get the alignment set where I wanted it. I figured out that when I tightened the bolts, the lock washers were pulling...
  7. Replies
    16
    Views
    477

    One thing that has changed is that dimensional...

    One thing that has changed is that dimensional lumber is now generally at 14% moisture or even a bit higher and is made from the center cuts of the logs. The rpms of your battery powered saw are...
  8. Replies
    17
    Views
    436

    They have a similar Kiosk at our local Lowes, I...

    They have a similar Kiosk at our local Lowes, I have never used it. I did need some new keys made for our church and the machine at the hardware counter digitally scans the key and then makes...
  9. I think you are wasting your time and may create...

    I think you are wasting your time and may create a bigger problem. Cedar is porous and absorbs water readily. If you seal the joints where the spports are any moisture that gets in through the wood...
  10. Replies
    6
    Views
    665

    Down at the bottom of every page is a "Contact...

    Down at the bottom of every page is a "Contact Us" button, you should be able to send an email to Keith using the form that opens up.
  11. Depending on how much you need to remove...

    Depending on how much you need to remove sometimes you can carefully cut one side free from the front and back and re-cut the dovetails or other corner joints.
  12. Replies
    3
    Views
    231

    53 years ago they started with the lightest...

    53 years ago they started with the lightest weight and worked up to the heavy weights.
  13. Replies
    6
    Views
    247

    Not necessarily, you could flip the work piece...

    Not necessarily, you could flip the work piece end for end and cut the second side.
  14. Replies
    6
    Views
    247

    A tapering sled that clamps the piece down on its...

    A tapering sled that clamps the piece down on its surface would work.
  15. I can't help with the connector, but, I lost the...

    I can't help with the connector, but, I lost the antenna of my electronic dog collar transmitter and found that any antenna with a matching thread works just as well. When I returned home I was able...
  16. For a plywood cabinet or chest of drawers I would...

    For a plywood cabinet or chest of drawers I would recommend using a Kreg jig and pocket hole screws from the inside to attach the top. This will hide the fasteners.
  17. Replies
    33
    Views
    3,608

    Most emergency services will simply pull the...

    Most emergency services will simply pull the meter out of the panel, which will kill all power to the structure.
  18. Replies
    6
    Views
    466

    I've used MinWax wood hardener and was satisfied...

    I've used MinWax wood hardener and was satisfied with the results. It won't help if the wood is too far gone, but for moderate punkiness it works pretty well.
  19. That's a really nice truck. The gas pump is...

    That's a really nice truck. The gas pump is great as well.
  20. I see this when using the mobile version, but...

    I see this when using the mobile version, but never when using the full site version except after Windows updates.

    My recommendation would be to tell SMC to remember you by checking the little box...
  21. Replies
    87
    Views
    4,939

    No problem, if you do future posts, remember that...

    No problem, if you do future posts, remember that photos are limited to 8 per post so immediately make multiple replies to your own post so that you will have consecutive space to cover your entire...
  22. Replies
    3
    Views
    285

    The 113 indicates it was built by Emerson...

    The 113 indicates it was built by Emerson Electric.
  23. Replies
    4
    Views
    282

    On a veneered top, I was able to remove a water...

    On a veneered top, I was able to remove a water stain by cleaning the area by wetting it with just plain distilled water. I had to do it several times before the wood evened out in color.
  24. Replies
    8
    Views
    505

    I'm not sure a cnc could make the cuts fine...

    I'm not sure a cnc could make the cuts fine enough and at the 5-6 degree angle. The work as I understand it has to use a pretty fine blade so the top and bottome edges will touch when the spiral is...
  25. Replies
    17
    Views
    797

    That's super. Congratulations to you both for a...

    That's super. Congratulations to you both for a major accomplishment.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4