Search:

Type: Posts; User: Dan Hahr; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    9
    Views
    814

    You will be wasting good plywood and making it...

    You will be wasting good plywood and making it harder to level the granite. The flat plane of plywood doesn’t add any strength in supporting the granite. Your granite installer will shim and level...
  2. Replies
    2
    Views
    925

    Sand it off if you can. Poplar sucks up stain. I...

    Sand it off if you can. Poplar sucks up stain. I wouldn’t use danish oil though. Use a good wiping or burnishing varnish instead.

    Dan
  3. Replies
    28
    Views
    2,388

    Find a decent builder supply and see if they...

    Find a decent builder supply and see if they carry CAMO screws. Check out camofasteners. Com. I buy them by the pound, usually 2-5 at a time. just to keep them on hand. I use them in olive green,...
  4. Replies
    19
    Views
    1,796

    4x4 pressure treated posts will make a disaster...

    4x4 pressure treated posts will make a disaster of a top. Rip some 2x12s down to whatever you can get and let them dry and settle. Then plane then down and glue them up in batches. Flatten each...
  5. Replies
    11
    Views
    1,070

    Just recut the dados a hair wider. Dan

    Just recut the dados a hair wider.
    Dan
  6. Replies
    11
    Views
    1,068

    You never know till you start cutting. Dan

    You never know till you start cutting.

    Dan
  7. Replies
    25
    Views
    2,192

    You might want to knock the corners off that...

    You might want to knock the corners off that steel piece. Looks like a knee buster.

    Dan
  8. Very simple fix. If it was flat with finish on...

    Very simple fix. If it was flat with finish on both sides, it will go back to flat with the finish off both sides. Sand both sides clean and stack on a flat surface on stickers in the same...
  9. Replies
    20
    Views
    2,035

    You could just saw off the bread board ends at...

    You could just saw off the bread board ends at the line just table side of the dowels. Pop off the ends. The joint will not be impossible to break. Recut the tenons and remake the breadboard ends. ...
  10. My Unisaw is 2005 x5 but still has a 1 1/4”...

    My Unisaw is 2005 x5 but still has a 1 1/4” arbor. I use it to cut 3/4+ all the time. There is not any arbor out past the nut but it works fine. At least 2 threads on the arbor. There’s a recess in...
  11. Replies
    10
    Views
    805

    Not if you want the door to be inset.

    Not if you want the door to be inset.
  12. Replies
    24
    Views
    2,039

    Yes. Sent the first one back because it dulled so...

    Yes. Sent the first one back because it dulled so fast. Second one dulled in the first 3 feet. You can sharpen them with a dremel but I’ve cut everything from copper to aluminum to maple with my...
  13. Replies
    24
    Views
    2,039

    Dulls very fast. Then wanders like crazy. Not...

    Dulls very fast. Then wanders like crazy. Not sure how it gets that bad so fast. See if you can get a Lenox Diemaster 2 blade. Wider kerf but stays sharp much longer. Kerf keeps it cutting...
  14. Thread: Drum Sander

    by Dan Hahr
    Replies
    64
    Views
    11,145

    Hmmm...which recommendation swayed you? Just...

    Hmmm...which recommendation swayed you? Just kidding...

    I couldn't help but look at Delta's site. Was really just wondering if the new Unisaw was still Made in USA. Never could get it to load. ...
  15. That is some kind of impatience. I don’t think...

    That is some kind of impatience. I don’t think that would be a feature on any jig saw. My Bosch probably stops in about a second. I do have to think about letting it stop before I pull it straight...
  16. Replies
    41
    Views
    3,795

    Kwik screws. Bought from cabinet supply shop. Any...

    Kwik screws. Bought from cabinet supply shop. Any cabinet shop should be using something similar.

    Dan
  17. Replies
    11
    Views
    735

    Stop switch was probably stuck depressed. Happens...

    Stop switch was probably stuck depressed. Happens to mine occasionally. Sharp bump loosens it just fine.

    Dan
  18. Replies
    13
    Views
    728

    Just put a couple strips of painter tape along...

    Just put a couple strips of painter tape along the template edge. A quick final pass will remove a few thousandths and any burning.

    Dan
  19. Replies
    6
    Views
    785

    Unfortunately, you will find that they rust and...

    Unfortunately, you will find that they rust and fail miserably compared to a quality deck screw like CAMO Screws.
    Dan
  20. Replies
    32
    Views
    2,034

    Not sure where you came up with this design, but...

    Not sure where you came up with this design, but it is lacking in strength and function. The design without stretchers will not protect against racking. The top attached only at the center will not...
  21. Replies
    13
    Views
    866

    Put it in your house with both sides open to air...

    Put it in your house with both sides open to air movement. Give it a couple weeks. It didn’t take any physical force to warp it. It won’t take any to flatten it. You have to allow enough time to undo...
  22. Replies
    13
    Views
    866

    Leave it on stickers and wait. When the moisture...

    Leave it on stickers and wait. When the moisture content equalizes. It will go back to flat. Don’t rush it.

    Dan
  23. Replies
    22
    Views
    1,478

    Definitely some good ideas for repairing an...

    Definitely some good ideas for repairing an extension cord. But if the rat just barely touched the copper and nothing’s broken, tape it up good and get on with life. If the wires break, then get...
  24. Replies
    3
    Views
    559

    Ramset. Hardened steel into concrete needs a lot...

    Ramset. Hardened steel into concrete needs a lot of power.

    Dan
  25. Replies
    13
    Views
    1,180

    My Diemaster II 1/4” blade is still going strong...

    My Diemaster II 1/4” blade is still going strong after several years of intermittent use. It’s not stamped either. As far as the rust, some one probably touched it with sweaty hands. No big deal....
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4