Search:

Type: Posts; User: Mark Bolton; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.31 seconds.

  1. Have you checked pricing at Wurrth? I've been...

    Have you checked pricing at Wurrth? I've been waiting to pull the pin on some Airvantage myself but remember checking surfprep pricing at wurth and was surprised. Still not as cheap as the air...
  2. Replies
    39
    Views
    1,045

    Ive been using Edge quite a bit lately. I am...

    Ive been using Edge quite a bit lately. I am really liking the new Windows all around but Ive always been an MS fan and I love change. I love an update when everything is new and different and...
  3. Replies
    2
    Views
    258

    Use to have woodcock at my property in WV and...

    Use to have woodcock at my property in WV and would see them often years and years ago. I have not seen one in ages. Always amazed me when I would see chefs cooking them up. Looked about like barely...
  4. Replies
    17
    Views
    523

    I would just buy a few bags of floor leveler,...

    I would just buy a few bags of floor leveler, float it all out flat, and toss as thin a substrate as needed over top.

    Any foolishness with routing or ripping out will be a colossal nightmare and...
  5. General Metalworking I have a metabo 6" electronic that I have loved...

    I have a metabo 6" electronic that I have loved for years. I'd hope their acquisition of Hitachi hasnt compromised their industrial line. Have two small 4" makitas that are fine and a dewalt....
  6. Replies
    22
    Views
    989

    Prashun's post just goes around in circles when...

    Prashun's post just goes around in circles when the real answer is simply if your in the hobby world, and what your making is for you, do whatever you like. Take 2 years to build a nightstand, if...
  7. We bump to 135lb slides on large drawers but on a...

    We bump to 135lb slides on large drawers but on a very large drawer that can still not be enough. A large/low pots and pans drawer for someone who has a lot of lodge/cast iron or perhaps fills a deep...
  8. I think there are a lot of instances where a pull...

    I think there are a lot of instances where a pull out behind doors make sense. Areas where you have something very tall stored with something shorter, areas that you want to keep modular where you...
  9. Keep in mind that the zero protrusion hinges are...

    Keep in mind that the zero protrusion hinges are massive and you will have to allow for the crank of the hinge in the closed and open position. Most people do as mentioned and block-in their pullouts...
  10. Replies
    12
    Views
    260

    You could pretty much hold them on with bubble...

    You could pretty much hold them on with bubble gum. No torque wrenches, nasa instrumentation, MIL specifications, necessary.
  11. Replies
    12
    Views
    260

    Not true. Every slide comes with numerous holes...

    Not true. Every slide comes with numerous holes for a multitude of different mounting options and assembly systems. Many standard slides installed with True32 will have only two screws or often times...
  12. Replies
    22
    Views
    989

    There is a massive amount of grey area in there...

    There is a massive amount of grey area in there that is generally ignored to simplify pushing people out to the extremes. The vast majority (especially those who are parting with their hard earned...
  13. Replies
    22
    Views
    989

    You provide the level of finish you are being...

    You provide the level of finish you are being paid for not what "you want" to deliver or what "you feel" it should be.

    In the grand scheme of things, other than on very large pieces, the cost and...
  14. The hour long files would only pertain to your 3D...

    The hour long files would only pertain to your 3D parts (which your original post said your not considering at this time). We cut miles of 2D parts for other businesses. The individual parts can...
  15. Thread: PVC Trim

    by Mark Bolton
    Replies
    20
    Views
    700

    Always filled with quad or any other urethane....

    Always filled with quad or any other urethane. May take 2 coats if you really want to try for smooth
  16. Replies
    13
    Views
    574

    Find a local or semi local source for off brand...

    Find a local or semi local source for off brand sold to cab shops. Mcfeely is insane expensive. If your buying 50-100 count boxes your stuck but if you can buy larger 2m boxes they are dirt cheap and...
  17. Replies
    7
    Views
    535

    Wow David, Holy cow, what a welcome sight!!...

    Wow David,
    Holy cow, what a welcome sight!! Man,... killer to see you.
  18. Replies
    22
    Views
    752

    I dont have much problem at all around my machine...

    I dont have much problem at all around my machine with or without ear protection. That screaming/rattling sound in your ear drums on a CNC (in my limited experience) comes solely from too much...
  19. Its never the fault of an inanimate object (no...

    Its never the fault of an inanimate object (no different than lopping a few fingers off on a saw) but there are enough responsibilities in business to stay afloat that having to be a babysitter,...
  20. Replies
    14
    Views
    493

    There is no way in the world you can hand feed...

    There is no way in the world you can hand feed flooring other than perhaps blank prep. unless your going hard core rustic. The end result would be a disaster.
  21. From the business side, this is why, as crappy as...

    From the business side, this is why, as crappy as it is, there are no headphones/music/or otherwise, allowed in the shop and as even crappier as it may sound other than on very rare occasions there...
  22. Replies
    14
    Views
    493

    I would simply opt for a 1Hp feeder if you can...

    I would simply opt for a 1Hp feeder if you can swing it if your talking about ripping and so on. The instant you set it up you will wonder why you didnt do it to begin with. Ripping becomes insanely...
  23. Replies
    14
    Views
    493

    If you dont want waste the climb cutting is wise...

    If you dont want waste the climb cutting is wise in that you will eliminate any and all catches and tearout that will blow out an entire tongue or the face edges of a groove. Conventional cutting...
  24. Replies
    121
    Views
    4,822

    So are you in an internal war here insinuating...

    So are you in an internal war here insinuating that anyone from an auto mechanic to a furniture maker to a high-rise architect, who evaluates the customers wants, needs, desires, in direct and solumn...
  25. Replies
    121
    Views
    4,822

    Reminds me of a bridge builder quote that I have...

    Reminds me of a bridge builder quote that I have loved for years that went something like:

    "The village idiot can build a bridge to carry a span, but it takes real skill to build a bridge that...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4