Search:

Type: Posts; User: Bruce Wrenn; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.55 seconds.

  1. Replies
    27
    Views
    893

    Purchase them separately.

    Purchase them separately.
  2. Replies
    11
    Views
    537

    Bommer hinges have an adjustment to change the...

    Bommer hinges have an adjustment to change the spring tension. If you look at the top of the hinge, you will see a cylinder with some holes in it, one of which will contain a short pin, that rests...
  3. Replies
    17
    Views
    918

    Fastenal is my first choice. Their store is three...

    Fastenal is my first choice. Their store is three miles from my house. If they don't have what I want in stock, usually it's there by 7:30 AM the next day
  4. Replies
    8
    Views
    368

    With State Fair less than two weeks away, spent...

    With State Fair less than two weeks away, spent some time getting things ready. We furnish "ground support" for Campers on Mission's State Fair ministry. They minister to the actual fair workers. On...
  5. VBX.or Fastenal are my first two choices....

    VBX.or Fastenal are my first two choices. Fastenal is the easiest, as there store is less than three miles from my shop. No need to go expensive, as these baring are "wear items."
  6. Replies
    7
    Views
    607

    No link to the video.

    No link to the video.
  7. Measure old cap, then hit Ebay and Amazon. One,...

    Measure old cap, then hit Ebay and Amazon. One, or both should have what you need. I ran into this on my DeVillbiss generator. It uses a 35 uf, 50mm X 80 mm cap. Also did my AP-400 with a remote cap,...
  8. Replies
    15
    Views
    1,312

    Have a NYW style panel cutter, Dubby, and most...

    Have a NYW style panel cutter, Dubby, and most used is a tiny sled. Tiny sled is approx 6" X 8", single runner, with ends trimmed, using left miter slot. Trim one end, and then reverse in miter slot...
  9. Replies
    10
    Views
    845

    Over at NC Woodworker there is a current thread...

    Over at NC Woodworker there is a current thread on a shop made quick tensioner
  10. Replies
    22
    Views
    1,341

    Look over at Ebay for some directional antennas....

    Look over at Ebay for some directional antennas. They come with built in rotor, which is controlled by signal sent thru co-ax cable. In college, I worked for local TV shop. In one area of town, we...
  11. Replies
    5
    Views
    1,228

    Been using that principal for years when building...

    Been using that principal for years when building router bases. I use pointed set screws, because I have them.
  12. Replies
    40
    Views
    3,185

    Don't take this as "fact." My right elbow has a...

    Don't take this as "fact." My right elbow has a life expectancy of 15 years also. Got 41+ years on it right now. Unfortunately, eight year old knees need some tuning up.
  13. Replies
    40
    Views
    3,185

    Hey, that's only two weeks away! Congrats on both...

    Hey, that's only two weeks away! Congrats on both the knee and retirement
  14. Replies
    8
    Views
    928

    Years ago, went to HD, and asked hardware guy...

    Years ago, went to HD, and asked hardware guy where could I find hardware cloth. With a straight face, he looked at me and said "If you want hardware cloth, you need to go to a fabric store." ...
  15. I have both that drill, in both straight and...

    I have both that drill, in both straight and right angle. It's a wimp when compared to my "Hole Hawg," which will spin a 8" hole saw all day without complaining. Ironically the biggest use of my...
  16. I feel the same about alcohol in gasoline. Liquor...

    I feel the same about alcohol in gasoline. Liquor was made for drinking, not driving.
  17. Watched a Video from ET Trucking last night....

    Watched a Video from ET Trucking last night. First fuel MPG isn't 50% more. Older trucks get around seven miles per, while newer gets about 8.5 MPG. Fuel costs are lower, HOWEVER, this doesn't...
  18. Replies
    14
    Views
    865

    Just the other day, wife said "Let me get MY...

    Just the other day, wife said "Let me get MY HAMMER." She comes back with a 22 oz, straight claw, Plumb, framing hammer, that looks just like the one I have been missing for years.
  19. Ah, the old "heat wrench trick."

    Ah, the old "heat wrench trick."
  20. Replies
    5
    Views
    1,092

    Remember that a typical shop vacuum will crush a...

    Remember that a typical shop vacuum will crush a bigger container, in a heartbeat. You might want to find an old shop vac bin, and adapt your dust deputy to it. Build a lid out of 3/4" ply with...
  21. For crisp dills,you will need calcium chloride....

    For crisp dills,you will need calcium chloride. Mount Olive Pickles has a 15 minute You tube video of their plant, and processing pickles. I know Kosher dills aren't brined. They are fresh packed,...
  22. Replies
    11
    Views
    780

    There is a poster over at NC Woodworker, who just...

    There is a poster over at NC Woodworker, who just bought (and received) a Harvey 14" saw. Several posts, about both the good and the bad.
  23. The Ball Canning book, or local Extension Office...

    The Ball Canning book, or local Extension Office would be my starting point.
  24. Several years back, we had hornets nest in attic...

    Several years back, we had hornets nest in attic between insulation and ceiling. They entered thru opening for AC line set. To get to them from above, meant having to roll insulation back, while...
  25. Because the sensor is part of the emissions...

    Because the sensor is part of the emissions system, it has to be submitted to EPA for verification (meaning it works as well as OEM one.) This is a lengthy drawn out process. But the government could...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4