Search:

Type: Posts; User: Richard Coers; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.12 seconds; generated 10 minute(s) ago.

  1. You should not test a square with a square. Who...

    You should not test a square with a square. Who knows which one is good. https://paulsellers.com/2011/12/checking-your-squares-squareness/
  2. Replies
    3
    Views
    240

    2 different animals. The Sorby allows you to...

    2 different animals. The Sorby allows you to change grits in seconds, but I never shop by internet popularity anyway. I don't see any on sale. $700 is one expensive belt sander.
  3. Replies
    27
    Views
    1,132

    I suspect the top bearings won't last long if you...

    I suspect the top bearings won't last long if you do bolt it to the floor. The vibration will still be in the machine and it has to go somewhere. That means the bearings. Take the blade off and spin...
  4. Replies
    16
    Views
    935

    I haven't moved anything that a railroad pry bar...

    I haven't moved anything that a railroad pry bar won't lift. 6' long, single tapered bevel end and with a block of wood as a fulcrum , the physics are there for a lot of lifting force. I recently...
  5. We are talking about a sleeve bearing, no shields.

    We are talking about a sleeve bearing, no shields.
  6. Replies
    17
    Views
    675

    Those mixer lifts are real space hogs. They...

    Those mixer lifts are real space hogs. They nearly take up all the space in the cabinet, and then protrude into walking area in the kitchen. My sealer is so small it's super easy to take out of a...
  7. Did you see my second link? It shows the half nut...

    Did you see my second link? It shows the half nut that engages the threaded rod/
  8. Replies
    16
    Views
    944

    It flexed when you were sanding it? Ease up a...

    It flexed when you were sanding it? Ease up a little, you don't have to sand that hard!!!
  9. Replies
    10
    Views
    649

    Hardly a plumber alive that would put some pipe...

    Hardly a plumber alive that would put some pipe dope on every fitting. I watched a video where the plumber added pipe dope to that rubber donut that seals the toilet tank to the bowl. What's the harm?
  10. Roller chain has been standardized since it was...

    Roller chain has been standardized since it was invented.
  11. And this instruction tells you about replacing...

    And this instruction tells you about replacing the threaded segment. https://incra.com/manuals/ThreadedSegmentReplacement_ins.pdf
  12. Here is what the manual says about maintenance; ...

    Here is what the manual says about maintenance;
    516981
  13. I thought only the Sanding Glove was the place to...

    I thought only the Sanding Glove was the place to buy his tools. The price list on Steve's website is dated 2022. https://www.thesandingglove.com/Advanced-Lathe-Tools-Boring-Bar-Systems.asp
  14. Replies
    16
    Views
    944

    No idea what kind of moisture meter you are...

    No idea what kind of moisture meter you are using, but to get zero percent moisture you must live in a desert there in Idaho. Fruit woods love to crack. No idea how that survived 1 year.
  15. Isn't there a plastic nut in the micro adjuster?...

    Isn't there a plastic nut in the micro adjuster? Better be careful with what lubricant you add or it could make that nut brittle or cause it to fall apart.
  16. The rest of the drive system will be a task. That...

    The rest of the drive system will be a task. That 3/4" shaft will make finding a small pulley a little challenging. You'll want a drive with very nearly zero backlash and a controller that will allow...
  17. Do you hollow 12-14" deep with the Bosch?

    Do you hollow 12-14" deep with the Bosch?
  18. Sure Tom, lots of them left. But they have to oil...

    Sure Tom, lots of them left. But they have to oil the thrust bearing just as often as anyone else. These sleeve bearings and sawdust just don't play well together. I'm not resawing and that is not a...
  19. Replies
    23
    Views
    1,786

    Neil Erasmus (designer/high end maker) That's...

    Neil Erasmus (designer/high end maker)

    That's a new title! Makes me chuckle! Where or how do you cross over from maker to high end maker? What is the monetary boundary between the two? So many...
  20. Replies
    13
    Views
    1,035

    In today's machinery, they use what at one time...

    In today's machinery, they use what at one time was called a safety head. Those came right after the square heads that could have a blade fly out. No worries now. Besides, if the bolts have stayed...
  21. Just to support you and let others see it's not...

    Just to support you and let others see it's not just you Simon. You have to keep an oil can around just like an old steam locomotive. If you don't the bearing drags and even if you don't wear a...
  22. Replies
    4
    Views
    546

    Not all generators are created equal. I bought an...

    Not all generators are created equal. I bought an inverter generator for the cleaner power situation for computers in the house. My feeling is that there are good people here, but not many...
  23. Replies
    23
    Views
    1,786

    Sure doesn't sound like a manufacturer. From the...

    Sure doesn't sound like a manufacturer. From the SpeTool website; JUCCI INTERNATIONAL CO., LTD., (International company of Hangzhou Fengchi Import & Export Co., Ltd.,), is an online retail company...
  24. Replies
    12
    Views
    956

    Unless the information I found is wrong, you are...

    Unless the information I found is wrong, you are way over catalyzing.
  25. Replies
    7
    Views
    676

    A little flour and water, paper machete, brushed...

    A little flour and water, paper machete, brushed on the paper will set it up nicely. Must be 50 videos or instructions on the internet of how to make them. But who gets a newspaper these days?
Results 1 to 25 of 499
Page 1 of 20 1 2 3 4