Search:

Type: Posts; User: keith micinski; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. I’ll take it

    I’ll take it
  2. Replies
    14
    Views
    1,073

    Get one of the new 3” cut off tools by any of the...

    Get one of the new 3” cut off tools by any of the major brands I do this work with it all of the time.
  3. Replies
    1
    Views
    2,994

    Makita track saw blade alignment

    Seeing all of these track saw questions has finally made me get around to asking this. Does anyone else have trouble getting there makita set back true to the blade at 90 after beveling? I have a...
  4. I have some of the same problems with my Makita...

    I have some of the same problems with my Makita track saw. It’s not off by much but if I tilt it from 90 it is a trial and error process to get it trued back up with the blade. I’m actually...
  5. Replies
    84
    Views
    28,689

    I use my makita to cut doors down as apparently...

    I use my makita to cut doors down as apparently pre 1990 doors were just made willy nilly and no two ever the same. I was anti track saw as hard as you can get for guy that says I got rid of my table...
  6. Replies
    45
    Views
    10,131

    It should be illegal to call those fruits.

    It should be illegal to call those fruits.
  7. Replies
    45
    Views
    10,131

    No one is going to mention the hideous hedge...

    No one is going to mention the hideous hedge apples, that are easily the biggest natural nuisance known to man kind? Thank your sister for me for cutting that blight on humanity down. Death to the...
  8. EVERYTHING!!!!!!!!!!!!! How did it take four...

    EVERYTHING!!!!!!!!!!!!! How did it take four pages for that to be the answer? If you remodel anything, ever, you will use it for every single trade. I also can't believe how many people are calling...
  9. Why would you use anything other then a table saw...

    Why would you use anything other then a table saw for that operation?
  10. Replies
    20
    Views
    4,969

    Thank you Dave

    Thank you Dave
  11. Replies
    14
    Views
    1,815

    I ended up mounting it about ten feet from the...

    I ended up mounting it about ten feet from the wall it exists and taking the exhaust side and bumping it up to 6". I had some insulated 6" flex left over and hooked it up thinking it might be a...
  12. Replies
    14
    Views
    1,815

    I do not have a cyclone I just exhaust to the...

    I do not have a cyclone I just exhaust to the outside. I will leave it where it’s at and make the exhaust 6” for the 12 feet to get out the wall.
  13. Replies
    14
    Views
    1,815

    I have a harbor freight 2 horse dust collector...

    I have a harbor freight 2 horse dust collector with a 5" outlet. I was worried about having a longer exhaust length would potentially start leaving chips behind causing a build up over time.
  14. Replies
    14
    Views
    1,815

    Longer exhaust run or suction run?

    So, I have to reroute my dust collection because right now where it used to dump outside is now inside a new addition. I can move the dust collector closer to the new exit and have a longer suction...
  15. Replies
    7
    Views
    1,236

    I have had that pipe sticking out the backside of...

    I have had that pipe sticking out the backside of the garage for about 5 years and just have a dryer vent on it that closes when not in use on its own. Not only did I never see any noticeable...
  16. Replies
    7
    Views
    1,236

    Not sure how long you would have to run the DC...

    Not sure how long you would have to run the DC for in any condition to actually affect the climate of my 1400 square foot shop.
  17. Replies
    7
    Views
    1,236

    Dust collection exhaust length.

    So I used to have my harbor freight dust collector just blow out the back side of my garage but I recently added an addition to the back side so I now have to reroute the dust collection. My options...
  18. I also want to hear more about this gauge. I...

    I also want to hear more about this gauge. I think your saying instead of relying on the rubber piece, that doesn't do much good as a straight edge because your right it gets all cut up and out of...
  19. Replies
    25
    Views
    2,784

    On this note I went to the store on Friday to buy...

    On this note I went to the store on Friday to buy a 125 or a 150 and really wanted to. I have heard nothing but great things about the festool sanders so I was really surprised at how much vibration,...
  20. Now you guys are making me regret not just buying...

    Now you guys are making me regret not just buying him a saw and running that one over.
  21. Listen, I’m not ruling it out, if he gets...

    Listen, I’m not ruling it out, if he gets frustrated with it I told him at any time let me know and we are bringing it back and running it over. I did put a new carb on the tractor and am hoping to...
  22. Bad news, that piece of crap sat around for the...

    Bad news, that piece of crap sat around for the last year mocking me and one of the guys that works for me finally decided he had to have a table saw at his house to start getting into woodworking...
  23. 1200 a window for a custom made wooden window...

    1200 a window for a custom made wooden window doesn’t sound the least bit expensive at all and building wooden windows from scratch with no experience seems like a recipe to end up with a lot of...
  24. Replies
    4
    Views
    1,768

    If you don't need anything bigger then that for...

    If you don't need anything bigger then that for the money it's as good as it gets. I love the old 735 which was a little bigger, and my new favorite tool of all time is a Milwaukee cordless table saw...
  25. Most guides have the cutout in the middle...

    Most guides have the cutout in the middle positioned in such a way that the two inside edges do the same function as the dowel pins do, I forgot to mention that in my post but the dowel pins is a...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4