Search:

Type: Posts; User: Günter VögelBerg; Keyword(s):

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. OK. I'll wait to hear back from Chappell. To...

    OK. I'll wait to hear back from Chappell. To make sure I was not insane I measured it again this morning and every square I have (including a starrett machine square) has it slightly acute. My...
  2. Framing square, I suppose, but not large enough...

    Framing square, I suppose, but not large enough for framing. A square made of a single piece of steel that lays flat. By imperial I mean graduated in inches. I agree about expecting it to be...
  3. I need a good 9x12 imperial square

    Can anyone please suggest a good square of this size, preferably with a center finding rule on one edge? I bought a Chappell square and it is not even close to 90, which is too bad because it is...
  4. I bought one at Costco this spring that has...

    I bought one at Costco this spring that has functioned well all season. It is not like the ones that "scrunch" together as they drain--those are, in my experience, generally garbage. This one is...
  5. Replies
    23
    Views
    753

    I learned to weld in a community ed shop. The...

    I learned to weld in a community ed shop. The best thing I did in that class was buy my Lincoln Viking 3350. It is far superior to the cheaper hoods they had. It responds faster, has more precise...
  6. Replies
    15
    Views
    1,274

    The only blades I have that I cannot sharpen with...

    The only blades I have that I cannot sharpen with the Lie-Nielsen guide are the skew blades of my Veritas skew rabbet planes. Lie-Nielsen doesn't make a set of jaws at that angle.
  7. David, that's quite the setup. I actually have a...

    David, that's quite the setup. I actually have a good incra miter gauge and could do that, but truthfully I rarely use my table saw for anything other than a 90. I usually use my miter saw for...
  8. I engage the lock at 90, tighten the bar into the...

    I engage the lock at 90, tighten the bar into the miter track but do not tighten the two knurled handles on top. With those handles loose I can move the fence in a pivot of about .5 degrees to the...
  9. Thanks for the input, but I don't think that's...

    Thanks for the input, but I don't think that's it. The problem is how the miter gauge locks in the angle. I took it off the saw and set it up on my bench and had the same problem.
  10. Suggestions for removing the slop from my grizzly sliding table attachment

    I have the cabinet saw add-on sliding table attachment that Grizzly sells and the problem I have is that there is a lot of slop that requires I use a square to reset it to 90 (or get any precise...
  11. Replies
    37
    Views
    1,412

    Is it just for the router or is it for the router...

    Is it just for the router or is it for the router and the modem? If your ISP requires you to "rent" their modem there may not be a lot you can do. If it is just the router then go on amazon and buy...
  12. I cleaned all the cast iron surfaces of my tools...

    I cleaned all the cast iron surfaces of my tools with the boeshield rust free then sprayed and wiped off two coats of boeshield t-9. I am now wondering if I should apply wax over the t-9 or if that...
  13. I wish I had tried the boeshield rust free before...

    I wish I had tried the boeshield rust free before wasting time screwing around with the other things. Amazing.
  14. OK, so I put naval jelly on the stains last night...

    OK, so I put naval jelly on the stains last night and I made the problem exponentially worse. Now the stains are spread around in the pattern in which I applied the stuff. I ordered some of the...
  15. In my samsung with the pull-out bottom freezer...

    In my samsung with the pull-out bottom freezer the lights are in the bottoms of the refrigerator doors.
  16. Please educate me about buffers and polishers

    A while ago I made the mistake of leaving some pressure treated wood sitting on my table saw overnight. In an effort to polish out the stains that it left I ordered some cheap wool polishing pads...
  17. Fair enough. I'm not actually making a point. ...

    Fair enough. I'm not actually making a point.

    Besides, I'm from Switzerland, so if you want kooky politics...
  18. I would not dispute this for a second. ...

    I would not dispute this for a second. California does a lot of things right. It must to have higher economic output than the entire UK, despite the kooky politics.
  19. I have had to redo a number of drains and I have...

    I have had to redo a number of drains and I have always found it is best to replace everything at the same time. Spend the extra $10 and save yourself some aggravation later. Also, if you go to a...
  20. Given all the insane ballot initiatives I'd say...

    Given all the insane ballot initiatives I'd say that it is California voters who fill that role. This is why Lie-Nielsen planes come with a proposition 65 warning.
  21. The thing is, though, with safety there are rules...

    The thing is, though, with safety there are rules that you just follow. You wear eye protection. You wear ear protection. You use push sticks. To me, after that it is about common sense. I just...
  22. We have a great mail carrier here. My wife...

    We have a great mail carrier here. My wife ordered a VERY expensive (like, several thousand dollars) piece of medical equipment and it shipped UPS requiring a signature. UPS said it was delivered...
  23. replaced a bathroom faucet installed new TV...

    replaced a bathroom faucet

    installed new TV antenna
    put ladder away
    re-installed old TV antenna
    put ladder away
    installed new TV antenna in different place
    put ladder away
    adjusted new TV...
  24. My rationale has always been that if I am wearing...

    My rationale has always been that if I am wearing thin, tight gloves then if my hand is close enough to the ouchie spinny to be a problem with the gloves then that is the problem--not the gloves I am...
  25. wearing gloves when using machinery

    I read on another thread criticism of the practice of wearing gloves while operating a table saw. I wear thin, tight-fitting nitrile gardening gloves most of the time when I am not doing hand tool...
Results 1 to 25 of 221
Page 1 of 9 1 2 3 4