Because when a lithium battery is left on the shelf it can go into a severe undervoltage condition which the cells are not designed to handle. Leaving cells in a low-voltage state for an extended...
Type: Posts; User: Greg Funk; Keyword(s):
Because when a lithium battery is left on the shelf it can go into a severe undervoltage condition which the cells are not designed to handle. Leaving cells in a low-voltage state for an extended...
Usually the airline app will show the boarding pass with its bar code. All you need to do is take a screen shot of the pass and call that up when asked to show it. I've never stored a pass in google...
Keep the bits and chuck the rest. Looks like a quick jig or test piece for cutting some very specific dovetail cuts. Chances of you wanting to make something similar to the original owner are slim.
That's what I would do. At the end of the day it makes no difference if the fence is at a slight angle like yours as long as it's square to the tables. Adjusting so you have an even gap between the...
Check that the 'caddy' or whatever it's called is level with the tables. It's attached with a couple bolts to the base and there may be some play involved when tightening the bolts
500674
Also,...
I don't see any adjustments on mine. Take a picture of the rear of the fence where it attaches to the adjustment mechanism. On mine the only way for the fence to be crooked like yours would be if the...
You must be used to bigger cheques than me :) We can deposit up to $500k with mobile banking.
Sorry - I was looking at 'New Posts' and got lost :)
I would cut them to table length plus a little. I don't see any advantage to milling longer boards. If your machines are setup properly the edges should be flat and square so no need to joint edges...
Where did you rent from? I rented a car in Toronto recently at the airport (National) and they gave me a Polestar EV but didn't need it charged when I brought it back. Just curious what the normal...
I think they're administered by a charging company for a monthly fee. Not as convenient or inexpensive as charging in a detached home but it's manageable.
To be fair most new condos in Vancouver are well over $1000/sq ft so the incremental cost of adding a charger outlet is relatively low. There are a few pictures here of some typical installations:...
It doesn't have to happen overnight as even when a high percentage of new cars are EVs there will still be a large number of ICE vehicles for the next 20-30 years. Around Vancouver all new Multi-Unit...
The range certainly goes down in the winter but most EVs still have way more range than needed for daily commutes. I only use about 25-30% of the battery on a typical day so if the capacity was...
https://www.ctvnews.ca/politics/what-is-bill-c-18-and-how-do-i-know-if-google-is-blocking-my-news-content-1.6286816
I use NordVPN to spoof my IP and make it look like I'm in the UK in order to watch bike races. Don't care about privacy. It is significantly slower than the fiber internet we have but works fine for...
In theory, if all the wires feeding the motor and the internal motor windings had zero resistance you'd be correct. In reality, when a motor starts it can easily draw 6 time the FLA amps which, for a...
The breaker should be a maximum of 250% of the FLA of the motor on the circuit (NEC table 430.52). In your case if the FLA is 12 the max breaker size is 30A so you should be OK.
Change the plug on...
Depends how big a cut you're making. I like to put a lot of pressure on the board and climb cut. I've only used a 1hp feeder and would probably be uncomfortable cutting the power by a factor of 8. It...
Yes they can sue you for negligence. Whether they'd win is another question. You would be wise to carry liability insurance.
Looks like a medieval torture device :)
And this is the crux of the argument. What's reasonable for you might not be reasonable for an experienced woodworker. No different than any other activity. I'm not going to take a young child riding...
I made a bunch of moldings for our house with this cutter. When it spins up you can feel it in your gut. I only ever used a power feeder but it's always a little unnerving when you make the first...
No problem sanding a tablesaw top. I've done it when some moisture got on the top causing rust spots. I'd figure out what caused the scratches before doing too much on the top.
As you get older I think quality of life is important. For me that means staying fit in order to continue to do the things I enjoy. Cycling has been a great way for me to stay in shape and socialize....