Rather than buy ready-made frames, I just used pieces of 1/8" by 3/4" aluminum bar stock from the home center for these. The notches were setup to support both letter and legal sized folders.
...
Type: Posts; User: Steve Wurster; Keyword(s):
Rather than buy ready-made frames, I just used pieces of 1/8" by 3/4" aluminum bar stock from the home center for these. The notches were setup to support both letter and legal sized folders.
...
There is a Classified forum, however you have to be a Contributor to post in there. Check out the Donate button near the top on every page in order to become a contributor.
Welcome to the Creek!
Hmmm, I'm going to guess the router table is blocking the outrigger support arm from moving. Ouch. I'm sure there's some way to work around this without having to throw out everything you've done.
The more information you provide about this table the more I want one. :) Now I'm just finding excuses to NOT rebuild my router table (the biggest two are material cost and the fact that mine still...
Wow, this is a tough one. Given that the instructions say "If attaching to Incra Miter Slider use ..." and then "If attaching to our Slider Bar use ...", it doesn't appear to be made by Incra. The...
I was eyeing that table top as a potential replacement for my "shop-made laminate-covered double layer of MDF" one that I built many years ago. Unfortunately the spacing of the T-slots won't work...
Only if you require a large (e.g. 55 gallon) waste drum. I have an Oneida V-3000 3HP mounted to the wall in my low ceiling basement shop with a 35 gallon waste drum. Of course I'm the only one ever...
I presume you mean the panel sled that Norm uses, where the fence is in front of the piece rather than behind it like when using a miter gauge? If you search online for "Norm Abram panel sled" you...
Ah, I see. I knew that Blastgate would customize things for you if need be. Just didn't realize you would need it here, but that makes sense.
That looks great. Good job. I really love the handle.
Jim, does iVac sell a gate that works with quick connect duct work, or will you have to put adapters of some sort on both sides of the gate?
I've had the same router for I think 14 years. I have zero free movement in the fine adjustment screw; that O-ring is apparently doing its job.
There is a small amount of movement in the turret...
Thanks. I apparently have watched some of that linked video before according to YouTube, but I don't remember when I did that. I'll have to watch the whole thing this time. lol
I have the same...
Per the OP's comments on the thread about T-nuts, this thread here helps make more sense about how the DRO is used. I have a Wixey leftover from when I had a contractor's saw, although it never...
The first style can be dropped in anywhere but doesn't lock, while the second and third style can lock but must be slid in from one end. I think the OP wants something that combines both.
Options...
Ah, right, I had forgotten that in your previous post you mentioned how you use the fence for a lot of your operations. I basically only use the fence for ripping pieces longer than the table, or as...
The point is that with the Incra setup you have very quick 1mm precision. If you need to cut something that is narrower than the minimum width between them then you can remove one or both flip...
The minimum clamping width is the same on both your jigs; just remove the stops from the Incra one.
You at least are using the miter fence-style Incra tracks there, where the locking knob is in...
Yep, I've got 2 pieces of "Incra Track" with 1/32"-based teeth, one on each piece of the F&F (not to be confused with their T-Track that has no teeth). There's no flip stop capability with this...
How much do you need, and where are you located in the Philly area? I've got this piece leftover from when I used part of it to make my router table top many years ago. It's been leaning up against...
I do the same with mine, although I can't remember if I got the idea from the Extreme Woodworker or not (been a while since I watched that video and I just redid my F&F very recently).
493115
Oh, I see how the ball works now. Yeah, that design won't really work on the slider unless the blocks are much larger. When I did use those on the slider I had them upside down compared to that...
No problem. Feel free to remove that!
1. I think the alignment ball only really helps with the 80-20 stuff or equivalent, and even then I'm not sure. I don't think it serves any purpose in this scenario.
2. That hex-cap screw is the...
These look to be the same as the 1/4-20 and 5/16-18 ones from Faztek. How are the 5/16-18 ones not wide enough? The 1/4-20 ones I have work fine; as you tighten the bolt the nut will raise in the...